Are there any studies on electrospinning of neat PEG?

More Ümran Aşçı's questions See All

Hello, the PSS we use for polymerization caused shrinkage on the material. What would you recommend to prevent this?

pedot, pss, conductive polymers

19 May 2024 4,826 2 View

Are there any studies on the influence of electrospinning parameters on TGA analysis results of the nanofibers?

I am looking for studies that investigate the effect of electrospinning parameters (solution and process parameters) on the thermal stability of nanofibers. Generally, the effect of nanofiller...

19 January 2022 1,888 7 View

How to perform BET analysis of Boron Phosphate?

I would like to know how one can perform BET analysis of Boron Phosphate.

01 November 2021 3,408 3 View

What is the best way to calculate porosity of nanofibers?

I am curious about how to calculate nanofiber porosity from SEM images.

01 November 2021 3,070 9 View

How to prepare a solution for GPC analysis?

I am looking for solution preparation methods for GPC analysis in order to find out the molecular weight of PLA. For the analysis, THF is used but I can't solve PLA in THF.

01 November 2021 2,021 10 View

Reasons for obtaining films instead of nanofibers after electrospinning process?

What could be reasons for obtaining films instead of nanofibers after electrospinning process like the one in the attachement?

22 September 2020 1,794 14 View

Detection of DNA Damage in proliferating cells?

I want to detect that my proliferating cells underwent a DNA Damage after treatment with drugs. I already know the H2AX method but looking for other methods. Many thanks in advance!

16 August 2020 4,285 6 View

Is it better to use anhydrous solvents for electrospinning process?

I wonder whether it is better to use anhydrous solvents for electrospinning process or not. In addition, what is a good alternative for electrospinning of PLA instead of 1,4-Dioxane in terms of...

03 May 2020 9,915 2 View

How can I prepare PLA (poly lactic acid) solution for electrospinning?

I've used Chloroform/DMF binary solvent system to dissolve the PLA at different concentrations. However, I've experienced clogging and multijet at the tip due to the fast evaporation of the...

02 February 2020 5,657 7 View

Do anyone want to write a common article about systems thinking or strategic thinking?

A cross cultural study for example.

10 December 2018 8,599 5 View

Ethylene glycol is newtonian or non newtonian fluid?

Some sources say it is treated as Newtonian as ethylene glycol has a higher viscosity than water, which affects the flow characteristics in simulations. But some also say it is non-Newtonian.

09 August 2024 2,111 2 View

In passive sampling, can polymer-lipid partition coefficients be applied independent of environmental salinity?

For example, if low-density polyethylene (LDPE) is equilibrated with PCB contaminated marine and freshwater sediments, can LDPE-lipid partition coefficients be used to obtain equilibrium...

28 July 2024 263 1 View

How can the rubber fibres produced by the electrospinning device be removed from the fibre collect(aluminium foil) ?

How can the rubber fibres produced by the electrospinning device be removed from the fibre collector (aluminium foil) without affecting the orientation of the rubber fibres for use in reinforcing...

26 July 2024 8,281 0 View

Can you recommend provider Intermediate laboratory test for hydrocarbon, polyethylene & polypropylene?

Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...

25 July 2024 8,108 0 View

VOC analysis on GCMS ?

Hi everyone, Can someone explain for me a method to inject VOC collected with Tedlar bag from pyrolysis process and transfer or inject into GCMS. Thanks

22 July 2024 6,398 1 View

How can I immobilize Glutathione on to PCL electrospun nanofiber?

Dear All, I need to deposit Glutathione on to ready made PCL nanofiber composite, how can I physically immobilize? which way of incorporation do you recommend, physical deposition or...

18 July 2024 9,725 1 View

How can I quantify MDEA (N-Methyldiethanolamine) with a GC-FID?

I have a mixture of glycol, water, MDEA, and piperazine. I want to analyze it with GC-FID.

15 July 2024 9,652 3 View

How can I quantify MDEA (N-Methyldiethanolamine) with a GC-FID?

I have a mixture of glycol, water, MDEA, and piperazine which I want to analyze with GC.

15 July 2024 2,181 10 View

How to quantify fibrin formation for absorbent hemostatic biomaterial ?

I have hemostatic nanofibers of hydrophilic nature. While fibrin formation from fibrinogen can be qualitatively visualized using SEM. What assays can be performed on nanofibers to quantify the...

08 July 2024 3,714 1 View

What are the engineering applications of polyethylene with waste tire rubber?

When polyethylene, whether high-density or low-density, is mixed with percentages of waste tire rubber, it becomes a new material. Where can it be used?

26 June 2024 3,349 2 View

Abdelkader BOUAZIZ

Dear Ümran Aşçı, may be you should search for neat Polyethylene oxide (PEO) electrospinning, since PEGs are low MW PEO. Please have a look at the following free access document. My Regards

https://link.springer.com/article/10.1007/s10853-020-05346-3

Following is another interesting document on PEO electrospinning. Good Luck

https://doi.org/10.1515/polyeng-2015-0057

Mahyar Saber

Hi dear Ümran Aşçı.

For optimal electrospinning, the polymer must have the desired molecular weight that PEG lacks, so an auxiliary polymer must be used.

Vishal Gavande

Follow the article

Ümran Aşçı

Abdelkader BOUAZIZ Mahyar Saber Vishal Gavande thank you for your valuable reply.