Is there any related studies or journals about the masonry building vibration assessment based on VC-curve (Gordon), which is due to ground borne vibrations from construction activities?
Thank you, Best regards.
See, please, Journal of Vibroengineering, Geliu Ratas 15 A, Kaunas, Lithuania, Lt-50282
Website: http://new.jve.lt/
Thank you Serge V.Shil'ko
Journal of vibration and control.
In my building vibration response analysis, I need to apply damping ratio of concrete = 2% which equals to 0.02 in material damping section. However, im lack of understanding regarding on which...
04 May 2015 7,092 3 View
Hai, I have read through a thread stated that " Implicit dynamic methods are used for simulating longer duration events (e.g., looking at the vibration of a structure following an impulse...
04 May 2015 4,430 5 View
Dear friends, Currently im performing my research regarding dynamic analysis of concrete masonry structure, by implementing macro modelling technique. I'm lack of understanding to obtain the...
03 April 2015 5,219 4 View
Dear friends, Currently im having two issues and uncertainties regarding on Abaqus analysis process: i. Does Abaqus CAE has the capability to perform linear perturbation of Frequency and Modal...
03 April 2015 6,175 4 View
In my study, i want to perform masonry building collapse as well as fracture response when subjected to large magnitude of ground-borne vibration. similar to the video link attached . Can someone...
03 April 2015 5,563 2 View
How can I create new points in ABAQUS to apply concentrated loads, where the points that aren't geometry points. Is there other method apart from partitioning?
03 April 2015 6,280 5 View
Dear friends, I have run a dynamic explicit analysis towards my model with acceleration input data in AMP>tabular, and it is applied on a single node. The tabular amplitude input data is...
03 April 2015 5,044 4 View
Currently, I'm facing difficulties to perform dynamic analysis of masonry building using time history data (Time vs acceleration) [due to ground borne vibration] . The data received externally in...
03 April 2015 6,143 6 View
From above question, does Abaqus has the capabilty to develop time history output from a numerical model analysis ,that can be used in MATLAB program ?
03 April 2015 7,129 8 View
Help needed , currently i'm trying to perform dynamic analysis/performance of multi story masonry building using ABAQUS program. i have obtained the vibrational data in "Time vs Acceleration" and...
03 April 2015 4,144 1 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,572 3 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...
20 July 2024 647 2 View
Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...
17 July 2024 1,501 1 View
I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...
16 July 2024 8,436 0 View
Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...
15 July 2024 3,491 0 View