A colleague of mine is researching conditions for arc welding of boron steel with stainless steel through GTAW. I haven't seen much literature on this topic. Can someone provide me with papers or report on this topic?
Article Weldability Study on SS 304B4 Joined using Boron Containing ...
Article Effect of boron contents on weldability in high strength steel
http://www.diva-portal.se/smash/get/diva2:778226/FULLTEXT01.pdf
Thank you.
See attached articles
What I want to find out: Women with high levels of aggression, impulsivity and alexithymia have a lower sense of parental competence than men with high levels of aggression, impulsivity and...
07 July 2023 1,571 2 View
What I want to find out: Women who have higher levels of aggression, impulsivity and alexithymia than men with higher levels of agression, impulsivity and alexithymia have a lower sense of...
02 July 2023 5,012 3 View
Is there any free software that can simulate pH dependence of adsorption of anions by carbonaceous materials?
25 October 2022 2,705 2 View
We calculated Hirshfeld charges at DFT/B3LYP level using Gaussian 09 software but will like to know if the program can generate Hirshfeld surface. Thanks.
08 September 2021 8,678 4 View
To perform protein solubility I will use the Brandfor method. How will I work with ph from 1 to 11, should I build my albomine curve with which ph of solvent? can you help me? 📷
23 August 2021 3,472 3 View
I am presently trying to study the crystalline quality of an ultra highly doped (substitutional, 10 at. %) homoepitaxial thin film. I know from cross section STEM and EBSD analysis that the...
07 June 2021 7,044 0 View
Hello, I am currently working on my Bachelor thesis and would like to find out how I should compute this on SPSS and which test I should use to find out how each group affects my dependent...
02 June 2021 7,577 3 View
I need some international support for a project proposal. Abstract Investigations of U alloys have been made due to their higher density, which makes it possible to build compact reactors...
25 May 2021 1,514 1 View
"We were trying to calculate excited state properties in solvent environment (e.g. ethanol) using CAM-B3LYP/6-311++G(d,p) and state specific PCM method in GAUSSIAN 09. There's however a challenge...
30 August 2020 305 2 View
It has been found feeding on Eucalyptus leaves in Indonesia. Family or genus, maybe? Thank you.
25 December 2019 7,146 3 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...
27 July 2024 7,168 2 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?
25 July 2024 9,408 0 View
I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...
24 July 2024 4,393 2 View
I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...
16 July 2024 5,047 0 View
In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....
11 July 2024 4,476 3 View
Would an average spot welder suffice for welding tabs for pouch cell electrodes instead of an ultrasonic one? Why would an ultrasonic welder be better than a regular spot welder?
10 July 2024 8,763 0 View