Anybody noticed that some journal editors reject the manuscript just by reading the authors' name or their affiliations ?
Dear researchers, I would be very grateful if any one knows which resin (epoxy or polyester) is better regarding the adhesive properties and wettability (which one is faster) with charcoal...
01 February 2018 971 2 View
Hi, I would like to simulate resin shrinkage due to cure process using ANSYS for residual stress analysis. The volume of the resin will decrease when changing to solid state. This also can taken...
04 May 2017 5,277 2 View
Is it possible using composite material with polyester matrix in wet places? Thanks in advance
01 February 2017 330 9 View
I just wondering why RG still not having an application for android. Now, the publicity of RG is wide and it is the time to think in android system users.
11 December 2016 9,014 41 View
Dear all, I am looking for an efficient software to plot plain weave fabric in 3-D and has the ability to be imported to ANSYS. I tried TexGen, but the imported "iges" file to ANSYS always...
31 December 2015 5,143 1 View
31 December 2015 9,818 14 View
Dear researchers, Why mostly the paper that published in high ranked journal will get better citation than if the same paper has been published in a journal without impact factor? Are we looking...
10 November 2015 334 5 View
To be honest, the peer review process is usually hard and time-consuming. The reviewer(s) exerted big effort in reviewing the manuscript(s) for free of charge. They usually contribute to improve...
10 November 2015 8,066 2 View
Hi there, I am facing a problem regarding the pretension loading. I need to apply axially uniform pretension load in the fibre prior matrix cure ( composite materials) and then releasing the...
10 November 2015 3,090 11 View
Editors Opinion
08 September 2015 10,099 1 View
Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...
07 August 2024 9,563 0 View
I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.
06 August 2024 6,796 3 View
As authors and academic writers, we usually prepare our manuscript using our own resources. We submit these manuscripts to scientific Journals for peer review and publication sometimes at a fee....
03 August 2024 7,304 2 View
It is being seen that Editors of some reputed Journals are putting on hold the manuscripts and not updating review states even passing more than six months from submission. Researchers are...
24 July 2024 8,596 2 View
"Integration of Mass Media and Communication into the System of International Relations: Place, Role, Actuality and Prospects: Modern Media Issues 2024" Website: https://immcir.alnoor.edu.iq/
23 July 2024 3,139 6 View
I am interested in publishing an updated version of my final master´s project in Spain and i am not sure which steps to take. I am open to suggestions.
16 July 2024 7,431 1 View
I came across the Green Building and Sustainable Architecture collection under Nature Scientific Reports some weeks ago. https://www.nature.com/collections/gajghaebce The special issue/collection...
10 July 2024 5,533 1 View
Is it appropriate to place the ATG codon in front of the gene of interest, since there is a secretion signal that has its own ATG in front of this gene? I need my protein of interest to be...
10 July 2024 3,050 5 View
Dear Friends and Colleagues, I have a question regarding the review process for journal submissions. When we submit an article to a journal, is it illegal for a reviewer to provide authors with a...
09 July 2024 7,557 7 View
Is there a way to add new Journals in the system?
03 July 2024 1,691 2 View