02 February 2018 2 976 Report

Dear researchers,

I would be very grateful if any one knows which resin (epoxy or polyester) is better regarding the adhesive properties and wettability (which one is faster) with charcoal particles.

Any helpful reference?

Thanks in advance

More Nawras H. Mostafa's questions See All
Is there any suggestion for modelling volumetric change in ANSYS?

Hi, I would like to simulate resin shrinkage due to cure process using ANSYS for residual stress analysis. The volume of the resin will decrease when changing to solid state. This also can taken...

04 May 2017 5,277 2 View

Can I use polyester resin in wet environment ?

Is it possible using composite material with polyester matrix in wet places?  Thanks in advance

01 February 2017 330 9 View

Why research gate does not have android app.?

I just wondering why RG still not having an application for android. Now, the publicity of RG is wide and it is the time to think in android system users.

11 December 2016 9,014 41 View

What is the best software for constructing woven fabric and can be imported to ANSYS for further analysis?

Dear all, I am looking for an efficient software to plot plain weave fabric in 3-D and has the ability to be imported to ANSYS. I tried TexGen, but the imported  "iges" file to ANSYS always...

31 December 2015 5,143 1 View

What is the best software for constructing woven fabric and can be imported to ANSYS for further analysis?

Dear all, I am looking for an efficient software to plot plain weave fabric in 3-D and has the ability to be imported to ANSYS. I tried TexGen, but the imported  "iges" file to ANSYS always...

31 December 2015 9,818 14 View

Is it true the researcher can get high citation if he published a paper in high ranked journals?

Dear researchers, Why mostly the paper that published in high ranked journal will get better citation than if the same paper has been published in a journal without impact factor? Are we looking...

10 November 2015 334 5 View

Why the peer reviewed articles (the accepted ones) didn't mention the reviewer names?

To be honest, the peer review process is usually hard and time-consuming. The reviewer(s) exerted big effort in reviewing the manuscript(s) for free of charge. They usually contribute to improve...

10 November 2015 8,066 2 View

How can I apply pretension in ANSYS for two glued parts?

Hi there, I am facing a problem regarding the pretension loading. I need to apply axially uniform pretension load in the fibre prior matrix cure ( composite materials) and then releasing the...

10 November 2015 3,090 11 View

Anybody noticed that some journal editors reject the manuscript just by reading the authors' name or their affiliations ?

Anybody noticed that some journal editors reject the manuscript just by reading the authors' name or their affiliations ?

09 October 2015 3,198 0 View

Why some editors stopping the process of a manuscript : Reviewer #1: reject, Reviewer #2: major revision, and Reviewer #3: minor corrections ?

Editors Opinion

08 September 2015 10,099 1 View

Similar questions and discussions
How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Do interactions between biosphere, carbon cycle, & water cycle impact global warming & interaction between atmosphere & hydrosphere?

How do interactions between the biosphere, the carbon cycle, and the water cycle impact global warming and interaction between the atmosphere and the hydrosphere?

09 August 2024 3,291 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close