When is it unnecessary to change organisational culture?

As a former management practitioner, I recall a generally accepted view that changing organisational culture is difficult, so you should only attempt it if the organisational change that you are...

27 February 2021 2,595 8 View

Can I use a protein-devoid condition as my negative control in ELISA?

Hello, I am running a sandwich-type ELISA where I am trying to inhibit a protein-protein interaction using small molecules. For each experiment, I determine my Z' (Z-prime) to determine the...

23 February 2021 7,429 1 View

Will SARS-CoV-2 Spike be broken into S1 and S2 by denaturing conditions?

Hello, I am performing a western blot of my SARS-CoV-2 Spike-pseudotyped lentiviral particles. I denature my virus by adding concentrated virus to 2X Laemmli buffer at 1:1, then boiling for...

17 February 2021 4,844 4 View

What is the best temperature to coat an ELISA plate?

Hello, I want to control the temperature of my ELISA plate during incubations to get consistent results. In general, what is the best temperature to coat the plate with antibody? I have been...

16 February 2021 2,377 7 View

SPSS - Merging files by ID numbers that contain letters?

Hi, I'm trying to merge files from a data base of 20 files, each containing about 4000 subjects. Unfortunately the ID numbers are actually a combination of numbers and letters (e.g., b1458219)....

15 February 2021 5,833 3 View

How would I go about getting an expert review on the interview questions for the dissertation?

Good Evening, My name is David Marshall and I am Doctor of Management Student at Colorado Technical University Online. I just recently received approval from the IRB to start data collection on...

08 February 2021 346 7 View

How can I quantify the color of a solution?

I know colorimetry has been the standard way by way of measuring the concentration of a particular compound (solute) in a colored solution (solvent or measure quantities of a particular compound...

08 February 2021 2,673 1 View

How to make Fast Green FCF from powder?

Hi everyone We need Fast Green to electroporate plasmid into mice embryos, therefore we simply need it to see some color in the liquid we are electroporating so that electroporation is more...

07 February 2021 1,671 2 View

ACE2 Blotted as a double band?

Hello, I have recently run a western of Vero cells for ACE2. I detected ACE2 at the correct size, but it presents as a double band. The sample was prepared by lysing cells in 1X Laemmli...

07 February 2021 6,973 3 View

SARS-CoV-2 Spike Protein Western Bands?

Hello, I am western blotting SARS-CoV-2 spike protein from lentiviral using an antibody against S1. To prepare samples, I mixed concentrated lentivirus 1:1 with 2X Laemmli buffer and boiled...

07 February 2021 3,643 4 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View