hi
i need the 3d profile dynamic air blast pressure in a non venting confinement.
who can help or addressed me about it?
Ithink , the P(x,y,z,t) can explained in P(x,y,z)*p(t).
p(t)=p0*f(t)
f(t) like a exponential or harmonic or combined of this function form.
so what is the p0?
what is the P(x,y,z)?
Hi every body I have some explicit analysis on plate under impactor. I need to extract the damaged elements in end of analysis with using python. who can explain this for me?
07 August 2019 7,462 2 View
Hi I have modeling the steel plate with thickness 28 mm, and slenderness ratio same as 1( L=2.4,B=0.8 m). the model post buckling under uni-axial loading analysis with Abaqus/Riks method. the...
08 September 2018 3,490 6 View
I make a shell model in abacus and mesh it. how can I **delete some elements** in this model?
04 May 2018 1,254 4 View
Hi I try to model a plate with in-plan loading for analysis of post-buckling. for some configuration of longitudinal stiffeners like as symmetrical stiffener section, the BC of long edges of plate...
03 April 2018 4,532 7 View
If you read the Kevorkian paper(attached), the over-pressure in experiment about 60bar at K4 sensor. But in my model (attached) with CEL technique, this pressure is near 20 bar. so,if you know,...
31 December 2017 10,048 1 View
HI HOW CAN I CONSIDER THE "CHAPMAN JOUGUET" PRESSURE IN ABAQUS MODELING FOR TNT AIR EXPLOSION?
11 December 2017 3,956 3 View
ANY BODY HELP ME ABOUT THIS PARAMETERS: ST-37 STEEL JOHNSON-COOK FAILURE PARAMETERS...
10 November 2017 6,177 0 View
I've been try to model explosion of TNT in Air(Eulerian model) and steel plate(Lagrangian) for finding the plate central node displacement and compare with Conwep blast analysis result. without...
07 August 2017 3,095 1 View
Hi I model a dynamic analysis and i will off a part at a moment in my analysis.how can I run this condition?
06 July 2017 1,076 0 View
Hi please Look at the attached pic. my part modeling damaged with some cutting holes.a few section of undamaged region is located within the void.in the meshing step,this sections create error....
02 March 2017 5,423 0 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
Air moisture harvesting Air water collection devices
06 August 2024 5,473 2 View
Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...
06 August 2024 977 1 View
We assume this to be true. We also assume that the vacuum bomb is the latest version of explosives with an explosive power of a few to ten kg of TNT equivalent. It has the unique characteristic of...
04 August 2024 4,534 1 View
Is this circle one of the rings?
03 August 2024 5,988 0 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View
In some data sources it has been grouped in Q1 and some shows it is Q2.
29 July 2024 4,227 2 View
Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...
28 July 2024 5,771 2 View
Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?
27 July 2024 648 3 View