Ansys System Coupling failure during FSI simulation?

17 February 2022 1 942 Report

"DP(0) A solver failure occured during the run in the Fluid Flow(Fluent) system."

Does anyone know about the solution to this problem? I have been sitting 3 months trying to solve this.What could be the possible causes?

It's a Transient Fluent+Transient Structural Simulation.

Note:I have run and got expected results with running just the fluent part(main part).

Thanks in advance.

Gopinath N K

Ahmed Abrar If it is a two-way FSI, the possible reason is fluid mesh is deforming more due to large deformations from the solid side. One standard answer is to reduce the time step size in fluent and improve the mesh quality. Also, have a relook at the re-meshing/dynamic mesh settings in fluent.

Badges
Science topic

More Ahmed Abrar's questions See All

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

I am interested in medicinal chemistry field, which books are highly recommended to learn from?

I am at the beginner level in drug design and drug discovery, and I am interested to learn more about this field. Which books are highly recommended to start from and gives me all essential...

02 March 2021 8,437 2 View

Could you please recommend some good journal that accept very long revie papers (approximately 6000+ words) in neurosurgery, cancer biology ?

01 March 2021 8,087 3 View

Does anyone have kinetic and kinematic dataset for gait classification?

I want to differentiate between normal and abnormal movement. For this reason, I am looking forward to this type of dataset.

01 March 2021 9,485 1 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

How to identify what type of fillers are in a polymer?

Hello everyone, I have some PHAs blended with fillers and nucleating agents, yet I don't know what kind of fillers or nucleating agents. The producer has shut down and there's no way to get in...

24 February 2021 1,356 8 View

Can't recognize exact phase and PDF card no of Silicon carbide in XRD?

We have deposited silicon carbide on carbon substrate using one PVD technique. Due to amorphous behavior of SiC at low deposition temperature, we performed heat treatment of those films at...

22 February 2021 2,072 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

High aspect ratio hexahedral mesh optimization solver?

I am interested in evaluating mesh optimization solvers that converge to high aspect ratio unstructured hexahedral grids. In other words, I am interested in a solver that optimizes warpage,...

26 February 2021 7,279 2 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View