Aluminum reduces inductance

More Ezgi Eren's questions See All

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

I want to create Amphiphilic Polysaccharide and PLA MPs by electrospray technique (single axial). Could you suggest suitable solvent ?

I know that PLA is soluble in DCM, not soluble in water and hard to dissolve in DMF. What kind of solvents will be suitable for electrospray system for the amphiphilic polysaccharide and...

13 October 2020 3,559 4 View

How can I model the laser melting effect on metal surfaces with ANSYS CFD?

Within the scope of my Ph.D. thesis, I want to determine the thermal distribution, melt pool, and melting/solidification processes in the relevant region by melting metal surfaces with a laser...

27 September 2020 5,097 3 View

Does anybody look Erasmus K2 Projects Partnership?

Hello All, We are currently looking for Erasmus K2 Project partner in Europeen countries. Are there anyone interested in becoming a project partner in the social sciences and (or technical...

10 December 2019 6,491 2 View

How to understand if CPU is thorttling back?

Hello everyone, When I have tried to solve quick example on Ansys, iterations took too much time and I think my CPU behaved strangely. The frequency is stable but the CPU %use is waving between...

16 March 2019 7,055 3 View

Ethanol contamination during elution of cDNA with TE in RNA-seq library prep?

I am using NEBNext Ultra II RNA library prep kit for preparing libraries from bacterial samples. When the libraries ready, I did second Ampure bead purification for those have dimer peaks. During...

24 October 2018 8,971 2 View

Multi step ahead time series forecasting in SVR?

Hi, I am trying to do multi step ahead time series forecasting by using SVR. When I do forecast for training dataset, the results are pretty good. However, when I do iterative forecasting by...

24 July 2018 4,713 3 View

Which way is better for batch anaerobic reactor? Continuous nitrogen sparging or one time sparging?

I am trying to grow Bifidobacterium longum in a anaerobic reactor. I use MRS+ L-cysteine for the growth media (which is also regular growth media). I maintain anaerobic conditions with N2...

07 March 2018 9,449 7 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

Have you ever experiencing air vent trouble in fermentation process?

Dear all, My research group is currently working with a 12-litre fermenter. Somehow, if we do the fermentation for more than 20 hours, the process will be more prone to contamination. Our current...

23 February 2021 1,908 2 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

What type of pressure sensor are usually used in microfluidics?

My team is designing a dual channel microfluidic chip that runs air and water. I think we've decided on the NE1000 syringe pump for it's versatility and feedback control. We will be ordering the...

18 February 2021 9,928 2 View

Not able to charge-discharge Li-ion coin cell at higher C rate ?

I am working on cathode material. I have made different Li-ion coin cell against Li metal using commercial available cathode materials such as LCO,LMO, LFP and NMC and also with the lab...

18 February 2021 1,450 3 View

Konstantin Pavlov

Hi Ezgi.

Answer-Collectivized electrons. Something very similar to "Loose Plasma" if I may say so. In simple words. Collectivized electrons influence each other Including magnetic component.

I hope this information was helpful.

Konsta

Ezgi Eren

Hi Konstantin. Many thanks for your help.