aluminum mesh coating with p25 tio2
What temperature is suitable for the calcination furnace for good adhesion on the surface of tio2 aluminum after coating? And does it matter if it has a ramp?
Dear Reham Dabboura
In the case of aluminum substrate it is harmful to go higher than 490oC and normally calcinations at 400oC is preferable.
Best regards
Mohammed Hussein j. H. Al'Atia
thank you
I need to the required sample ,reagents and steps
10 December 2020 7,087 1 View
The total pressure loss = 1 bar Pump efficiency : 25%.. I need to know the approach, the work flow, the equation needed please. Thanks in advance
14 March 2020 9,783 3 View
oral mycosis infection
11 September 2019 6,746 3 View
more information about thermophilic bacteria
11 August 2019 6,750 1 View
the blue circle in uv graph can consider as the head of graph and can i take this points the value of the wavelength of nanoparticles ? in the photo with number 1 this graph indicates that there...
09 August 2019 158 1 View
first image for SNPs synthesized by certain plant, while second image is the UV of plant extract without silver nitrate i think the wavelength of SNPs start from 300 to 450 nm? thank you
06 August 2019 5,311 2 View
Solve equations
15 May 2019 5,924 4 View
I want to remove THF from my polymer (Tecothan) . If I use the vacuum oven ,it will affect the homgeneity of the formed layer?? Or not?? Is there any solution for this problem?
15 November 2018 3,825 2 View
I have two bottles of cell culture media MEM Hanks and 199 Earls I dont need them now, but i will later. How can I preserve them for about 6 months , without loss in nutrients or contamination ?
24 May 2018 3,138 3 View
02 August 2017 1,391 2 View
We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...
03 March 2021 7,975 3 View
Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...
01 March 2021 8,220 2 View
I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....
28 February 2021 7,967 3 View
Do we immerse the bricks horizontally or vertically ? #bricks#waterproofingsurface#civil#engeenering#chemicalengineering#wax#parafinwax
28 February 2021 6,685 2 View
I want to use 0.1% gelatin. Should that be made in PBS or sterile water? Should I autoclave the gelatin soln after making it in water/PBS?
28 February 2021 274 2 View
I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...
27 February 2021 1,829 3 View
It's a hydrolysis reaction, which may produce by either acid or base-catalyzed reaction. so can anybody help me with this, which condition is suitable for this reaction?
26 February 2021 1,760 8 View
Hello, recently I am having some difficulties with maintaining the cell culture of primary cells isolated from a skin biopsy (normal and malignant). The coating of culture plates with Matrigel (a...
26 February 2021 6,151 2 View
Hi, We culture neural progenitor cells in T175 culture flasks coated with PLO-Laminin. We have successfully grown these cells with our protocol for months. Recently, we observed large sheets...
25 February 2021 3,443 4 View
During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...
25 February 2021 7,994 3 View