I am comparing simulated vs experimental values of Current pulse discharge test of LiFePo4 2.5Ah battery. The maximum error value I get is 21mV and mean is 10mV. Is it acceptable ? What is the acceptable RMSE for a battery model ?
I want to carry out reliability study of a machine with various sub components both electrical and mechanical. The machine is a one time use (similar to a decoy or rocket) and is stored at...
30 June 2024 2,435 0 View
home based bio waste management
02 June 2024 8,590 4 View
Dear friends, I am looking to develop a new project for the applications of displays using float glass. How and what process is needed to develop such flat panel displays what are the ideas and...
09 May 2024 3,233 0 View
Dear ResearchGate colleagues, professors, and scientists, I'm encountering challenges with coated thin films produced using a sputtering system. Following treatment through tempering at 650...
11 February 2024 3,585 4 View
Hello everyone. I am trying to analyze the NOx study for my cementitious TiO2 material. According to the ISO standard, I have to follow 1000 ppb and 3 L/min of working fluid. In my case, I have a...
17 January 2024 7,266 0 View
I have read a research paper "Development of a novel morphological paclitaxel-loaded PLGA microspheres for effective cancer therapy: in vitro and in vivo evaluations". I want to synthesize PLGA...
13 December 2023 9,857 1 View
I have done metabolite fingerprinting of plant extract using LC-MS and GC-MS.
29 November 2023 4,511 3 View
They seems synonymous terms describing the same phenomenon.
24 October 2023 4,332 0 View
I am looking to deposit a single-layer titanium nitride layer with a sheet resistance of approximately 60 ohms and a layer of TiNx (x value should be in the range of 0.8 to 1.2). The developed...
22 October 2023 7,594 4 View
Please mention name of open source software
02 October 2023 2,301 3 View
I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...
13 August 2024 9,795 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View