ABAQUS 6.14, shell to solid conversion

More Silambarasan Ragunathan's questions See All

Can anyone identify the species?

Dear all, I have collected the specimen from Visakhapatnam fishing harbour. I have little confusion for identification of the species. If possible any one identify the species.

10 May 2020 4,384 7 View

What is the Algebra structure ?

I have proved some property. 1. Idempotency, 2. Commutativity, 3. Associativity, 4. Absorption law, 5. Distributivity and 6. De Morgan's laws over complement. what is the structure of this...

28 April 2020 9,534 4 View

Can anyone identify the Wrasse species?

Sir, I collected the fish from Visakhapatnam fishing harbour in Gillnet catch. Can any one identify the species.

17 January 2020 4,191 5 View

Can anyone explain how many degrees of freedom in Chi-square test?

Hi, I worked in Probit analysis. I made Chi-square test for LC50 analysis in fishes. My value is 24.1. I have some doubt how many degrees of freedom will come in the above said value. I have 10...

22 September 2019 6,823 4 View

Identify this fishes?

Hi Everyone; Please identify this fishes collected from the exploratory trawl survey at a depth of 62 m off Visakhapatnam coast.

24 August 2018 9,135 13 View

Can you suggest me which technique is good for electropolymerization of polymers in (TiO2/nanocomposite) nanotubes?

Because I want fill the polymer in the nanotubes. Also I tried by applying constant potential like amperometry techniques. I need suggestion for deposition of polymers on TiO2/nanocomposite nanotubes

29 October 2017 3,523 3 View

Can any body identified this Barracuda species?

Dear Sir, I have collected this barracuda species from Kasimedu fishing Harbnour, Chennai coast. If you possible kindly identify species level. Regards, K. Silambarasan

05 September 2017 743 10 View

Can somebody help identifying this fishes

Dear All, I have collected this fishes from Visakhapatnam fishing harbour. I think three species in Gobids and other one is very difficult for identification. Can anybody identify this...

25 July 2017 8,040 3 View

Is there any computer program to calculate phase matching angels of biaxial crystals?

Since it is difficult to directly solve the phase matching equations for biaxial crystal systems and to find out the incident phase matching angles(θ and ф), please suggest me a computer program...

26 July 2016 4,820 4 View

How to find out the Type 1 and Type 2 phase matching angle for a biaxial ( monoclinic) system , if the refractive behaviour of a crystal is n2>n1>n3?

The formulas to find the phase matching angle for a biaxial crystal system is available only for the refractive behaviour of n1>n2>n3 or n3>n2>n1. But how to find the optic axis for...

03 February 2016 3,281 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Stability of the Solar System: Insights from Einstein’s Equations ?

The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...

07 August 2024 2,569 1 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View