Hello, how can I define a variable rotating speed in ansys for a vertical axis wind turbine?..
Thanks
you should define UDF for time variable speed.
Thanks sir, do you know how to do this?
Ahmed S. Mansour hello sir, i am doing the same thing, have you got any UDF for variable speed?
Hello dear Tariq Ullah Yes I used the dynamic mesh technique using 6 DOF solver. I uploaded this tutorial. Check it out please. Danke!
https://www.youtube.com/watch?v=vrhHs6QbyTU&list=PLH4HEP9c_pKOAG19b3axqdJbZmagGCTop&index=29
Ahmed S. Mansour thanks
Viel Erfolg ! Tariq Ullah
Hello, I have a simple model (PV cell+ air channel) and I do not know how to let the sun rays hit the PV surface and then transfer the heat to the air..What I see is the sun rays hit the air...
08 September 2019 688 2 View
Hello, I need the equations that show the coefficient of the matrix that solves the velocity contours of the boundary layer over a flat plate. I have the explicit discretization equations but I...
05 June 2019 8,078 4 View
Hell, how can we write a UDF to include a heat flux value + convection coefficient for a wall in Fluent because we cannot define two named selections for 1 wall ? Danke!
05 June 2019 7,188 12 View
Hello, I want to simulate the half of the domain and define a symmetry wall because I do not want to consider it as the edge wall, I want to consider it the wall at the half of the domain..How ca...
04 May 2019 6,100 3 View
Hello, I want to know how to use ANSYS Chemkin to model the attached model in the attached paper. the videos on internet are so simple. Thanks
04 May 2019 4,064 2 View
Hello, we have done a simulation using ANSYS FLUENT, can we couple it with ANSYS simplorer? And if yes, how and what are the documents I can study? Danke!
03 April 2019 2,799 6 View
Hello, I have a wall which is affected by a heat flux and it is cooled by convection..How can we do this in FLUENT? Thanks
02 March 2019 6,112 4 View
Hello, we wanna write a thesis and we need the equations used for simulating the temperature distribution over a PV panel.. Where can we get these equations that ANSYS uses ? Thanks
31 December 2018 5,908 5 View
Hello, we have a CFD code written in MATLAB and we wanna save the calculations at a specific node to a text file like ANSYS FLUENT..Any suggestions please? We will be extremely grateful! Thank you!
31 December 2018 934 3 View
Hello, I have this UDF and it says that the airfoil changes the degree to +/- 8 through 1 sec, how is to work and how can we control the angle? /**********************************************/ /*...
09 October 2018 4,673 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am working on developing a MATLAB Simulink model of Wind turbine with PMSG followed by MPPT Boost converter. I have gone through so many literature and videos but I am not finding clear solution...
03 August 2024 888 1 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
I am looking to predict some production for future onshore wind energy production in Portugal, is there any database with info of performances of the existing wind farms in the country? something...
28 July 2024 1,750 1 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View
Due to the shifting ocean currents, the planet could be thrown off balance, altering the angle of rotation, and even causing the axis to shift, plunging us into chaos. In reality, it doesn't take...
15 July 2024 8,949 1 View
Let me say I have a solar plant in operation and I want to build up a wind power plant, and later make a hybrid so that I could power the electrolyser as load for green hydrogen production.
14 July 2024 9,547 4 View
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View
"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...
13 July 2024 8,621 5 View