3D Transfection of mRNA in a 3D cardiac model?

01 August 2023 0 5K Report

I want to transfect mRNA in 3D cardiac models.

Assays using Lipofectamine or iTOP didn't work, and I didn't find any method that efficiently reaches the center of 3D models.

Thank you for your help!

Badges
Science topic

More Axelle Bois's questions See All

Could you recommend me a good waterproof (at least rainproof) data logger recording temperature and relative humidity, or relative humidity only?

I would like to deploy data loggers in the field and need one which could survive heavy rains as we can have here in the south west of England. Ideally i am looking for a waterproof one as the...

27 September 2017 8,907 9 View

I need an app that reminds my participants every morning to fill in 8 questions. I tried PACO but I'm having serious problems with getting no ping?

It should work on iOS and Android.

03 April 2016 1,034 3 View

How many theca cells does a mature human ovarian follicle contain?

citable references appreciated...

15 August 2015 7,125 7 View

Does anyone have information about protocols for nitric acid etching on opaque microcrystals?

I wish to enhance the visibility of the successive growth phases of opaque crystals (mostly pyrite ; 5-200µm) in optical microscopy thin sections. I understand I have to use nitric acid etching....

23 February 2014 5,632 6 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

The Optimal Experimental Approach for Gene Function Analysis?

What is the most suitable experimental setting to understand the consequences of a particular gene: (1) targeted degradation of the specific transcription factor (TF) of the gene, followed by...

04 August 2024 6,265 1 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View