Contact experts in Heat to get answers
2,399 views 1,522 posts
Questions related to Heat
Myself Nekin Joshua R, Research scholar from Vellore Institute of Technology(VIT), Vellore. I need a drop weight testing facility. Please let me know where it is available in India ( Preferably...
28 March 2023 7,383 3 View
I have attached the simulation file of MATLAB 2021b of the PI rectifier. The three-phase sinusoidal voltages are good at the input side but the three-phase current is non-sinusoidal What should I...
27 March 2023 8,305 0 View
Experimental and computed temperature histories in gas tungsten arc welding of thin plates, Welding Journal Research Supplement, Vol. 48. pp 295s-305s, (1969),Pavelic V., Tanbakuchi R., Uyehara 0....
21 March 2023 3,094 0 View
This question is for creep specimens.
18 March 2023 6,959 2 View
Hello! If anyone can help me with data on the stress supported by bismuth telluride (Bi2Te3) legs in thermoelectric generator applications (published papers or manufacturer data or anything...
06 March 2023 5,109 2 View
converted unit from dynamic viscosity to gm / mole
04 March 2023 8,731 1 View
Nitration of anhydrous Ethanediol is done with Adding 65% Nitric acid with excess 98% sulfuric acid around 100 degrees C (adding one chemical drop by drop on mix of other two, allowing copious...
03 March 2023 1,776 2 View
Using Abaqus how to analyze diffusion rate in resistance spot welding
16 February 2023 2,909 1 View
Hello, I'm trying to simulate the separation of solids (crystals formed by a crystallizer) and a liquid on ASPEN PLUS using centrifuge filters (CFuge), but I'm getting this error: ** ERROR...
13 February 2023 8,338 1 View
I need help simulating PV DSTATCOM for power quality improvement using evolutionary-based optimization techniques to enhance the performance of DSTATCOM
02 February 2023 4,219 3 View
Hello everyone I am undergraduate student of Chemical engineering I have an assignment in which we are given with problem statement to Develop a simulation of any non-conventional equipment in...
22 January 2023 876 2 View
have to make a brief analysis and capacity of the plant is given and operating pressure is given only? (design of Kettle reboiler in gas purification plant of capacity of 100 MMSCFD, operating...
07 January 2023 6,379 1 View
I tried writing a udf for the turbulence model needed to validate a study. The wall boundary conditions (epsilon and f) specified for the v2-f model are available in the code I wrote. While I get...
12 December 2022 6,630 1 View
Dear, Now I am working on the process modeling for CO2 capture, but not sure about the typical industry diameter for a packing type absorber and stripper. Could anyone give any suggestions? I...
17 November 2022 7,874 0 View
My question is that if we want to remove CO2 from a gas stream that contains 20% O2 and less than 5% CO2, what are the best solvents list? The solvent should be able to remove CO2 in very low...
16 November 2022 9,851 5 View
Hi I am trying to simulate evaporation of gas R134a using Lee model in VOF, the problem is during the boiling process the bubble forms but the temperature of the liquid is increasing more than the...
24 October 2022 6,644 2 View
I need to find the electronic states of strontium hydroxide. while, the binding energy difference is small.
23 October 2022 317 1 View
I have modelled solid slab and I have assigned bottom face of slab as Elastic support but that elastic support is needed to be modelled for compression only spring.
17 October 2022 4,400 3 View
In our radiation laboratory we routinely trap respired 14CO2 from soil, after incorporating 14C labelled substrates, using NaOH traps which can then be mixed with scintillation fluid and activity...
14 October 2022 7,176 1 View
Dear, I am looking for a list (excel or else) of a large variety of surfactants (from natural origin if possible). If anyone knows a website that references a lot of surfactants, It would be very...
11 October 2022 1,970 3 View
This is in reference to the diesel fuel specification with respect to China VI, Euro VI, BS VI and Wordwide Fuel Charter 2019 wherein the Flash point varies from 35 to 60 deg C. While flash point...
12 September 2022 7,710 1 View
I must remove (1) steam and (2) dust particles from flue gases. But there is too much pressure drop if I use multiple equipment for both (e.g. a steam condenser/ heat exchanger and cyclone/ ESP/...
12 September 2022 5,291 3 View
I have determined the activation energy of XLPE material using TGA by iso-conversional method (KAS) at conversion of 5-10% . But now it is very doubtful which value of Ea should be used. Moreover...
23 August 2022 1,437 0 View
When calculating C input, how much rhizodeposition by cotton and green gram root residue should be taken into account?
01 August 2022 3,246 0 View