Contact experts in Heat to get answers
1,429 views 1,243 posts
Questions related to Heat
For example investigating the entropy generation number or entropy generation through heat and mass flow
11 October 2020 4,635 4 View
I am looking for a wear detection method for a pipe that goes under intense heat and pressure for short instances at intervals. this process has an average cooldown time of 8 seconds between each...
09 October 2020 3,887 2 View
I have data from an experiment where we looked at the time-to-death of pseudoscorpions under three treatment conditions: control, heat, and submersion underwater. Both the control and heat groups...
01 October 2020 5,346 3 View
Is there any DNV clause for shell side nozzles' projections of shell and tube heat exchanger. I want to keep the outside projection of the shell side inlet and outlet nozzles to 3" with 1" bore on...
30 September 2020 7,014 3 View
Hello, I'm about to start a new industrial project in which we want to estimate (interpolate) the INDOOR temperature at unknown 3D positions in possibly complex 3D room geometry based on sparse...
29 September 2020 4,267 3 View
As the excessive as well the insufficient heat lead to complex changes in the microstructure as well the grain structure of the base material due to which the materials property were affected. How...
24 September 2020 9,867 20 View
Male Infertility is a major public health concern worldwide and there had been heated debates to date on the above question; in other words is Boxers vs. Briefs related to Increasing Sperm Count...
22 September 2020 2,487 12 View
In solar desalination still, the water is heated by the absorbed solar energy. At some point, the temperature in the still reaches the boiling temperature. I would like to understand the...
10 September 2020 1,104 3 View
Any of your precise suggestion would be highly appreciable.
10 September 2020 4,857 4 View
I have written code for a for a Heat Exchange Reformer in Aspen Custom Modeler, but it cannot run. The program describes a shell and tube heat exchanger with steam methane reforming reactions...
08 September 2020 2,137 9 View
I have been trying to calculate heat function value by the equations given in the equations.png file. The geometry is a rectangular cavity with isothermal sidewalls and the top and bottom walls...
07 September 2020 778 4 View
BCS equation corresponding to electronic heat coefficient is given to the attachment.
07 September 2020 6,237 3 View
How to calculate Nusselt number if an enclosure is heated from two sides (horizontally and vertically)?
03 September 2020 1,555 8 View
We are doing heat inactivation of ligation reaction at 65 C after 12 hours of incubation at 16 C but we are having a problem in getting colonies.
01 September 2020 8,083 3 View
In general stove heat moves from the bottom to top in even manner. But in case of micro oven most of the times top layer only we get more heat compare to bottom. What could be the possible reason.
30 August 2020 3,242 27 View
When we radiate a solid film with gamma radiation, the film will experience a temperature rise. But we don't have access to the film to measure the change in temperature. How to calculate the...
15 August 2020 9,750 5 View
Multi-phase flow instabilities in liquefied natural gas cryogenic heat exchangers affect flow distributions in the system adversely. This consequently has negative impact on the energy consumption...
31 July 2020 9,748 2 View
For cooking pots to work on an inductions stove ferromagnetic material is needed. However, aluminum foil does not contain ferromagnetic material. With a thickness of 0.016 mm the aluminum foil is...
30 July 2020 6,409 5 View
Dear all, I have modeled a building in TRNSYS. I am cooling the building using the radiant panel on the roof integrated with simple cooling coil and other heat recovery devices (like enthalpy...
28 July 2020 8,184 1 View
Non-metallic materials such as brick stone and brick are good absorbers of solar energy, especially if they have dark coloring. Material with low thermal conductivity insulators they do not...
24 July 2020 5,672 5 View
I want to decide effective heat transfer area for thionyl Chloride, so require above said questions answer.
27 May 2020 9,393 5 View
I am considering to purchase the EuroClone SafeGrow 188 Direct Heat CO2 Incubator for growing of sensitive pluripotent stem cells. Have you good experience from this incubator?
05 May 2020 8,500 0 View
I am working on simulating Welding using the Goldak Double ellipsoid heat source model in ABAQUS. But I am not sure how to define the heat source as mentioned in the equation and also defining the...
28 April 2020 4,795 1 View
The reaction was carried out isothermally at 3 different temperatures during reaction time (temperature during dosing of isocyanate remains the same at all 3 different reaction temperatures). I...
28 April 2020 7,513 3 View