Review and cite FORCE protocol, troubleshooting and other methodology information | Contact experts in FORCE to get answers
8,027 views 1,433 posts
Questions related to Force
Dear sirs! An old Vario EL III elemental analyzer was purchased. Could you share the Manual for its operation in PDF format With respect,
17 March 2023 911 0 View
the detail is about that when i create a model which can predicts the stability of landslide dams with missing values.I know that XGB or lgb model is good at dealing with missing data ,but i dont...
14 March 2023 2,020 2 View
What is the relationship between the degree of polynomial fitted in response surface analysis and the number of input and output variables? For example, how many degrees of polynomial should be...
13 March 2023 9,068 1 View
I'd like to model the hydraulic effect of the implementation of beaver dam analogs (BDA) in a stream using HEC-RAS. For that, I need to establish a relationship between the water level upstream...
13 March 2023 803 3 View
The command line gmsh -2 hexagon.geo -o hexagon.inp creates an Abaqus model. However, the element type should be S4 instead of CPS4. How can I achieve that?
08 March 2023 8,931 0 View
A simple pin-pin column , and the Euler buckling load is Pi^2/L^2*EI. If I have a uniform lateral load, then the deformation of column as a bow, what will be the new Elastic Buckling load, is it...
06 March 2023 2,640 2 View
I am looking to design and further running simulations and analyse a low speed shaft of a typical wind turbine. In particular I am looking to design the shaft diameter and length and any other...
05 March 2023 8,766 0 View
1. I am so much interested in the Modified Garabedian McFadden technique, I am interested in getting the optimal value of the A, Band C values. 2. During the inverse design of an airfoil, some...
01 March 2023 9,697 0 View
Nuclear Power Reactor Safety E. E. Lewis(1977)
26 February 2023 8,052 5 View
i am a junior engineer (Hydrologist). Currently i am working on chiniot dam project. during flood study its observed that measured or Observed flood value is greater than estimated flood value....
23 February 2023 974 6 View
there are several Electromyography books but I'm looking for a functional book with new updates and editions to read.
21 February 2023 9,217 2 View
I have created a rectangular model in ABAQUS, and I am trying to create Oblique sections within the model so that I can assign different material properties to each section in order to create...
20 February 2023 8,667 2 View
Hi everyone. I am a student learning how to use Gaussian. I have been trying to run optimization-to-minimum calculation in S1 state for methane molecule. However, looking at the electronic...
16 February 2023 4,208 2 View
One of the three fundamental components of a Digital Twin is Twin Data. Can you provide an accurate and precise definition of the term 'Twin Data'?
14 February 2023 6,144 0 View
I hope everyone is fine and everything is going well I have a question from you: From time to time, the ResearcGate site sends the titles of articles from certain researchers for my use, this is a...
14 February 2023 3,223 7 View
Hello. I am working with a water cluster, and I only needed to optimize one face. So, I used the option atoms noatoms to define an atom list and indicate which atoms are to be optimized, and which...
08 February 2023 7,160 1 View
Gell-Mann's Construction : up = (1/2, 1/3, 2/3) (Spin, Strangeness, Charge) top = (0, 2/3, 2/3)...
06 February 2023 8,418 11 View
Hello! I have a few questions about a TDDFT calculation that I ran ( # td b3lyp/6-31g(d,p) scrf=(iefpcm,solvent=chloroform) guess=mix) and when I calculation the % probability of some of the...
01 February 2023 4,350 4 View
The theory of evolution said that man is a biological gradient of apes? Why don't we think the other way around? Maybe apes were a biological gradient of man?
31 January 2023 6,155 1 View
Hello all I have two questions; 1- First of all, is it possible to generate HIT inside a rectangle? If so, it is called HIT again? 2- if Nx=Nz but Ny is different, How can I calculate power...
13 January 2023 3,155 3 View
I installed Gaussin g09 and GaussView 6 in ubuntu 18, but when I wanted to run the program, I got this error, so I don't know how to fix it. Thanks for your cooperation.
12 January 2023 9,563 0 View
10 January 2023 7,177 0 View
there are six reactions that they are not linear or Arrhenius, so i need use some txt program to insert in app, but i don't know how? can anybody help me?
07 January 2023 9,117 3 View
Can someone teach me on how to change the feed rate of the friction stir welding in abaqus simulia ?
07 January 2023 6,135 2 View