Review and cite DEVICES protocol, troubleshooting and other methodology information | Contact experts in DEVICES to get answers
18,179 views 1,485 posts
Questions related to Devices
I am doing the TCAD simulation of MOSFET devices. In such devices, an electrical dipole layer exists at the oxide/silicon interface. I was wondering if anyone would tell me how to set this dipole...
24 November 2021 8,511 3 View
I want to make a decision making device by nearby active bluetooth devices using HC-05 bluetooth module with arduino nano but I stucked at programming algorithm to find active devices. It is...
24 November 2021 7,740 4 View
I try to set up an AcquireX workflow for out Orbitrap. I selected an MS1 experiment and an MS2 experiment with exclusion list, run 5 samples, but in the end it looked as if no MSMS/file has been...
19 November 2021 7,357 0 View
Currently, in my country, tachographs are installed only on vehicles carrying out international traffic (AETR agreement). When transporting inside the country, no devices are used to monitor the...
17 November 2021 6,407 1 View
I am modeling Graphene based devices with CST and MATLAB. My main simulations are related to wave absorbing by the structure but I need to know regarding thermal effects due to absorption. How I...
31 October 2021 1,960 4 View
Is there a blood flow test setup that can measure the amount of blood a CPR device delivers from the heart to vital organs during compression?
31 October 2021 7,969 3 View
Despite being the tool of surging interest in recent years, there is a huge gap between lab experimentation regarding electrospinning and its industrial impact, because of the obstacles...
30 October 2021 2,123 0 View
In order to calculate trans-membrane pressure(TMP) of a dead-end ultrafiltration unit, how do we measure pressures at inlet and outlet?
26 October 2021 3,630 3 View
Hi, I would like to gain more insights on HEMT figures of merit (cutoff frequency f_T, maximum oscillation frequency f_max, breakdown voltage BV, on-resistance R_on, maximum drain current I_dmax)...
17 October 2021 8,319 1 View
I am designing a novel type of power system capacitor, and a colleague suggested I investigate what effect the induced magnetic fields would have on the device. The device is like an old airgap...
15 October 2021 2,192 3 View
Hello everyone. I'll start working on my master thesis and my task will be to simulate a SDN architecture with some IoT devices in a 5G environment. I've read that Simu5g (http://simu5g.org/)...
08 October 2021 8,218 3 View
Due to the integration of new and legacy technologies in 5G and applying Artificial Intelligence (AI) and Machine Learning (ML) which are bring more benefits of innovation and supplier diversity...
05 October 2021 4,454 1 View
Dear community, does anyone have suggestions on papers which adress the influence of surface chemistry (which is e. g. altered by surface treatments) on adhesion of different adhesive types? I...
30 September 2021 323 4 View
Good day everyone. Is the Normalized Standard Deviation only parameter for measuring the accuracy of the Multiline TRL? Is there any other way to show the effectiveness of Multiline TRL? Also,...
25 September 2021 7,213 2 View
Hello all, I am trying to measure the response time (On and off speed) of a photodetector. I use Keithley-4200 with 0 bias (applying light on and off) to measure current with time and calculate...
21 September 2021 3,900 1 View
I'm new to the research on electrochemical energy storage devices and am trying to better understand the fundamental relationship between potential and current density. 1. In evaluating the cell...
18 September 2021 1,331 0 View
Hello everybody. I want to simulate the effect of Ag on the structure and electronic properties of CdTe. For this, I chose the cubic structure of CdTe and calculated the electronic properties in...
17 September 2021 9,688 3 View
Using ultimaker cura I am using ultimaker CPE transparent for printing . How to optimize for its 3d printing and which type of parts can be made through it.
14 September 2021 3,955 1 View
I add. this command but i am not sure about it( Beam=100 x=301 y=150 s.right)
10 September 2021 10,030 3 View
In Markov model of the system, I am using minimum repair, when the system is in absorbing state again I applied minimum repair to bring it back to the working condition. But When I tried to find...
09 September 2021 5,572 3 View
Hello, I am currently working with boron-doped diamonds films and I want to use GDOES to determine the [B]/[C] ratio to better understand the boron doping in my samples. Does anyone know how to...
09 September 2021 9,431 0 View
Hello, I need to know why shorter impedance matching(IM) transmission line has higher Band width? (for example in designing IM circuit which has been calculated by Smith chart the shorter solution...
02 September 2021 2,304 10 View
Basically, I have start calculations on WEIN2K for 2D structure but i was troubling in an issue of force convergence. I can not run SCF by using min_lapw command due to not convergence of force.
29 August 2021 7,138 1 View
1. Goal: Research with EEG and with neurofeedback in future. Howeover I am completely new in the field so i need a time and practice 2 Price is crucial. I wanted to buy Emotiv EPOC flex (2000USD)...
27 August 2021 1,861 2 View