Contact experts in Calculations to get answers
3,017 views 1,763 posts
Questions related to Calculations
I am using 25 wt% of ammonia water for OFET based ammonia sensor. In the equation for calculating concentration of ammonia in PPM,One Mass ratio term is there( Mass of ammonia in ammonia water)....
05 May 2017 4,191 0 View
Please provide if you have any direct calculators
05 May 2017 7,926 0 View
Schild plot
05 May 2017 7,440 5 View
I have a source: Co-60 and measure a dose equivalent equal 31.73 x 10^-6 Sievert (by FDM 1000 detection) ( distance from resource to detection equal 1cm, time= 45 minutes). Can i calculate the...
05 May 2017 856 12 View
Hi all, I am trying to get the 0 and infinite frequency dielectric constants using Vasp. How to set in Vasp. Thanks .
05 May 2017 9,426 2 View
How to calculate the comulative probability vs operating voltage of a memrister devices
05 May 2017 8,515 0 View
Hi there, I am examining the denaturing effect varying concentrations of ethanol have on alk.phos activity and I have a problem regarding calculating the standard deviation. I'm plotting Percent...
05 May 2017 7,229 2 View
How can I calculate LD50 of a substance?
05 May 2017 5,598 0 View
Non
05 May 2017 575 0 View
i need to calculate Skin friction drag computationally...Any Help
05 May 2017 2,901 0 View
I have read papers regarding special k points for different unit cells but i am unable to understand that how can i calculate the k points for fcc unit cell, and how can i calculate for different...
05 May 2017 4,333 0 View
how to calculate the coefficient of friction between polyester and polyurethane
05 May 2017 8,764 0 View
Hi, after a review I received an observation like this "the results of ABGD shows a high level of uncertainty and of ambiguity: choosing a different prior intraspecific divergence from Appendix 1...
05 May 2017 6,121 4 View
I am using A123 26650 LFP battery. How do I calculate the time constants (tau) from Voltage time graph of battery. I am using 2RC equivalent ckt model. Thanks
05 May 2017 9,079 1 View
The GE official protocol says I need 50mM Cl2Co, so should I calculate only by the Cl2Co MW? Thank you!
05 May 2017 1,314 2 View
I want to calculate the concentration in terms of ug/ml for core/shell (CdSe/ZnS) QDS. size is 3nm found from TEM. I calculated the concentration in terms of Molarity but I got stuck in converting...
05 May 2017 5,075 0 View
When we are considering single gas flow, then how can we relate stage-cut with pressure variation? How can we relate only CO2 gas flowing through the membrane with stage-cut?
05 May 2017 9,623 0 View
an equation for reacted fraction
05 May 2017 6,186 0 View
I have calculated inflow for lab scale UASB reactor as 0.4L/hr whereas the re circulation rate that I have got is 3L/hr I have calculated recirculation rate by following formula Vup= {Q(inflow)+..."> Can inflow rate be lower than recirculation rate in UASB in ANAMMOX process? We use cookies to make interactions with our website easy and meaningful, to better understand the use of our services, and to tailor advertising. For further information, including about cookie settings, please read our Cookie Policy . By continuing to use this site, you consent to the use of cookies.
05 May 2017 5,743 1 View
Rotary piercing is a hot working metalworking process for forming thick-walled seamless tubing.
05 May 2017 1,701 1 View
How can we calculate the swim speed and swim depth of fresh water reptiles?
05 May 2017 8,941 2 View
I'm working with oscilloscope and i would like to analyze the output voltage and the pulse state. Can i know the time, pulse state or calculate the electron from anode. Please explain for...
05 May 2017 3,749 0 View
any suggestion on calculating the doping ratio [B2H6:SiH4] of p-type silicon nanowire (SiNW) based on growth (CVD) recipe/parameters or measuring the doping ratio of the NW via characterization...
05 May 2017 1,259 2 View
I am runing a multilevel modelo where the dependent variable is the ln(costo) and I have two levels, can I use smearing in stata?
05 May 2017 5,451 0 View