27 Questions 15 Answers 0 Followers
Questions related from Somanath Nirali
I am unable to get the hourly solar radiation data of my study area Mumbai, Maharashtra. How can I get hourly solar insolation data of Mumbai, India?
11 November 2018 6,649 12 View
Dear friends I am simulating diffuser with changing divergence angle to check the pressure coefficient If we compare the experimental and computational value, they are not satisfactory. The...
08 August 2017 1,814 4 View
I am doing CFD analysis of waste heat recovery from flue gas to remove moisture content from coal particle. I think This is problem regarding Discrete Particle Method In fluent. But Hoe to add...
03 March 2017 6,869 2 View
I want to simulate cyclone separator with discrete phase and moisture content (evaporation and condensation ) using star ccm. If anybody has tutorial please share it.
02 February 2017 6,042 1 View
we know we can define enthalpy at constant pressure. But what is enthalpy at constant volume? Is enthalpy is equal to internal energy in constant volume process?
11 November 2016 2,898 3 View
I am simulating spray atomizer. Cold Water is rotating through rotating chamber. It comes out as droplet from nozzle.Hot air is coming in contact with water droplet . which model should I use for...
06 June 2016 5,349 8 View
In Ansys workbench we can split face using tool is it possible to split body in ansys workbench? If yes , how?
05 May 2016 2,677 8 View
I am trying to simulate rotating spray dryer with water and air as multi phase. I got error in meshing The mesh file exporter failed during translation. Please send your data to your support...
05 May 2016 9,232 3 View
Does any body have fluent(mesh) file of this tutorial? http://dl.racfd.com/tank.pdf
05 May 2016 6,421 2 View
I am simulating radiator with water as hot fluid and air cooling fluid. water is flowing through tube and air is flowing around tube(like cross heat exchanger). BC Water inlet - mass flow rate...
05 May 2016 9,509 3 View
Does Anybody have fluent model and udf file of this tutorial?
03 March 2016 4,828 4 View
I Have shell and tube heat exchanger with 192 tubes. I am facing problem of meshing in workbench. Is it possible to convert this problem in terms of Heat exchanger model in fluent?
02 February 2016 2,786 2 View
I am simulating 2D Heat pipe which is divided into three part , evaporator, adiabatic section, condenser. I have don simulation in which water is converted into vapor in condenser section. Heat...
01 January 2016 7,154 1 View
While defining material property of water in fluent , we have one term- stander ad state enthalpy . Is it calculated or taken form steam table? If calculated , how it is calculated?
01 January 2016 7,421 5 View
By using evaporation and condensation model, we can convert water into vapor (saturation temperature and heat input to evaporator ). But how to convert vapor into water in condenser section? Is it...
01 January 2016 7,626 3 View
I was solving tutorial of simulation of solar absorber plate with water flowing through absorber tube. I am unable to give coupled wall condition between fluid surface (water) and solid surface...
12 December 2015 1,382 9 View
I want to simulate heat pipe in fluent with 2D geometry ?? what is procedure ? will you provide some link of tutorial
12 December 2015 8,447 1 View
I am simulating temperature distribution of water around condenser in two case. 1) condenser is filled with water vapor 2) condenser filled with ethanol vapor More amount of heat rejected in...
10 October 2015 6,178 3 View
I want to simulate part of condenser in heat pipe which is surrounded by helical tube using ANSYS fluent. Heat is rejected from condenser which is saturated steam. That Heat will be given to...
09 September 2015 1,160 13 View
Generally we use fin for rejection of heat by increasing surface area. Can we use fin as heat addition source?Fin is attached at outer surface of pipe. Heat will flow from pipe to fin. Let us...
06 June 2015 6,806 5 View
hi , I am solving fluent tutorial related to particle laden flow which has some UDF function. when I load this file I get error. Please help me to solve this problem please tell me difference...
03 March 2015 5,476 8 View
i want to know when to use multiphase and species model. what is basic difference between them?
02 February 2015 1,573 9 View
I am working on nano particle in Ansys Fluent. I want to know which models can be used in simulation. Is DPM okay?
01 January 2015 4,117 7 View
I am trying to mesh mixing tank with rotor in ansys workbench. WARNING: Unassigned interface zone detected for interface 28 WARNING: Unassigned interface zone detected for interface 31. I got...
01 January 2015 5,993 4 View
I have problem with specifying blending factor 0.9 where can I specify this blending factor in FLUENT
11 November 2014 1,776 2 View
I am simulating T junction with hot and cold water as inlet . Can anybody tell me how to specify momentum ratio in fluent?
11 November 2014 7,529 4 View
coputational fluid dynamics
10 October 2014 2,938 4 View
