Zircorium silicate Glue

More Kadir Ejderha's questions See All

Illustra™ MicroSpin™ G-25 columns what it is used for?

Hello, We found three packages of Illustra™ MicroSpin™ G-25 columns in the cabinet of an unused lab. They are very old but have never been opened. I have never used this kit before, and I couldn't...

25 July 2024 4,927 3 View

How Through Silicon Vias (TSV) simulated in Silvaco?

How can we simulate TSV in the Silvaco example? Exactly, I need the instructions for the attachments file. Best regards.

29 May 2024 1,638 1 View

Removing Nonpolar Impurities from Methanol Extract-which solvent do you recommend?

Hello, I have a methanol extract that I have let stand for 3 days, three times. I have evaporated the methanol and, just to be sure, mixed it with water and lyophilized it. Before performing HPLC,...

20 May 2024 1,847 13 View

How to purificate Curcumin metal complex?

Hello, After synthesis curcumin metal complexes, how can I purificate molecules with 1:1 and 1:2 metal-curcumin stoichiometry, and is there any reference study on this matter? In the literature,...

04 April 2024 8,571 4 View

Can I use hypotetical proteins as a novel peptide?

Hello, In the literature, there are some MS/MS results that include hypothetical proteins, which can be shorter than 40 amino acids. I can also find these when I search for an organism in the...

04 April 2024 5,098 2 View

Is it possible to perform antimicrobial docking with a whole organism?

Hello, I've recently started exploring molecular docking applications, and I'm still in the early stages.I'd like to ask which proteins should be considered when examining the antimicrobial...

03 December 2023 738 4 View

How to perform molecular docking using a synthesized peptide?

Hello, I've recently started exploring molecular docking applications, and I'm still in the early stages. I'd like to ask Can I choose a ligand by giving the amino acid sequence and then do...

03 December 2023 3,074 3 View

Can I use the standard calibration curve of <10 ppm to calculate the higher concentration of unknown sample by using the equation (y=mx+c)?

The standard calibration curve that was prepared was 0 to 10 ppm but the maximum concentration of the unknown sample would be 30 ppm. Can I still use this standard calibration curve to find the...

31 October 2023 4,081 1 View

What is the most suitable method for assessing the antimicrobial activity of colorant substances- that produce excessive color- ?

I have a few substances that resemble curcumin, and I need to conduct antimicrobial tests, especially MIC experiments in a 96-well plate, with these substances. However, these substances are...

02 September 2023 6,143 4 View

Hi, I was able to dye polyester fabric with natural dyes at 85 degree Celcius for 60 minutes. Is the any explaination on this?

The details as per attached

15 April 2023 5,581 2 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

Separation of organic acids-HPLC?

Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.

07 August 2024 8,782 3 View

RNA later for the preservation of RNA in fecal samples at room temperature for one day (37°C)?

I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...

06 August 2024 1,367 3 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Is it possible to improve the reforming section of the Haber-Bosch process without using air separation units?

A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...

01 August 2024 7,051 5 View

How to improve peaks separation in HPLC?

Hi everyone, I'd like to better separate two close peaks coming from a bioconversion sample, I'm currently using a C18 KromaPhase 4,6mm Ø.I. SCHARLAU, particle size (µm): 10, pore size (Å): 100,...

30 July 2024 435 3 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

AGILENT HPLC 1100 SERIES , any expert available please?

AGILENT HPLC 1100 SERIES operation assistance needed.

25 July 2024 10,045 2 View

Is it possible to do transient simulation in HFSS in presence of magnetic biasing?

I have designed magnetic material with different biasing conditions in HFSS. Now I want to give an RF AC signal and do a transient simulation in HFSS. Is it possible to do in HFSS? Please help me...

24 July 2024 9,319 5 View

Kadir Ejderha

Selamun aleyküm

I am trying to make a glue using zirconium silicate high temperature low outgasing glue.

I need it for the cryostat at our lab.

I have zirconium silicate powder, but i am wondering which solvent to use for preparing the glue

Joe Orti

had you tried cyano acrylate?

cyano acrylate is not stable on high temperature