Would you recommend me the books or thesis about clay minerals relation with volcanic activity. ?

More jo Jaeguk's questions See All

Anyone who tell me how to measure concentration of hydrogen in soil?

i want to know concentration of hydrogen(mol) in soil. how to measure it?

08 September 2017 5,943 0 View

About identification of XRD results?

i want to know about identification of XRD results that each pick positions. as a result of qualitative and quantitative analysis revealed O, Na, Mg, Al,Si, S, K, Fe, Cu, Zn etc.. personally, i...

07 August 2017 2,394 3 View

Identification of XRD results for synthetic jarosite?

anyone who help me about XRD results for synthetic jarosite? i synthesized K-NH4-jarosite mineral under the 90℃ (120h) using morey-type reaction container, and approximately 300mg of the...

07 August 2017 3,476 5 View

I want to verify the existence of jarosite in clay fractions by quantitative and qualtitative analysis on SEM analysis.

i want to confrim the existence of jarosite in clay fractions by quantitative and qualtitative analysis on SEM analysis. and i also wondering that whether it is distinguish of jarosite mineral...

06 July 2017 469 0 View

Anyone who tell me about the condition of silica gel dissolution by pH transition using reagnet in room temperature

i want to make a homogeneous state for mixing materials (i.c. silica gel powder(Na4SiO4), Al2O3 (l), Fe-sulfate powder, Mg-acetate powder etc.. ) in room temperature. just i used KOH solution to...

04 May 2017 5,056 0 View

XRD results for synthesized smectite, about analysis technique?

i tried synthesis of smectite, and it was measured by XRD. however, too initial intensity is so high to do not show the other peak such (001), or (02-11) reflections. how can i control such high...

01 February 2017 4,427 2 View

About EPMA data; (WDS only), for smectite.?

i analyzed for smectite (i.e. montmorillonite or saponite) by XRD, but sometimes it is difficult to be sure that between saponite and Fe contained montmorillonite at (060) peak position. so that...

31 December 2016 1,991 1 View

I want to know about the formation of NH4(gas or aq) from the combination N2 gas with H2gas; below the conditions?

i want to know about the formation of NH4(gas or aq) from the combination N2 gas with H2gas; below the conditions. just i think that N2 gas derived from magma reservoir, but the production...

10 November 2016 751 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How can we differentiate between calcite, dolomite, siderite, magnesite and ankerite minerals in carbonatite rocks in thin section under op microscop?

How can we differentiate between calcite, dolomite, siderite, magnesite and ankerite minerals in carbonatite rocks in thin section under optical microscope?

07 August 2024 2,132 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View

Meenakshi ..

I would suggest you the publications of Prof. J. P. Shrivastava from University of Delhi. He is working since 36 years on clay assemblages formed from Deccan basalts.

Smectite is the major mineral in the clay fraction originated from volcanic rocks.

Amit Kumar

J. P. Shrivastava

Sucharita Pal