I want to verify the existence of jarosite in clay fractions by quantitative and qualtitative analysis on SEM analysis.

07 July 2017 0 469 Report

i want to confrim the existence of jarosite in clay fractions by quantitative and qualtitative analysis on SEM analysis. and i also wondering that whether it is distinguish of jarosite mineral structure by SEM images ?

just i confirmed that existence of jarosite by XRD analysis (attach the XRD image).

Badges
Science method

More jo Jaeguk's questions See All

Would you recommend me the books or thesis about clay minerals relation with volcanic activity. ?

I want to study for clay minerals originated from volcanic materials. Mineral identification; pretreatment methods, analytical techniques, SEM observation etc.

05 June 2018 3,226 2 View

Anyone who tell me how to measure concentration of hydrogen in soil?

i want to know concentration of hydrogen(mol) in soil. how to measure it?

08 September 2017 5,943 0 View

About identification of XRD results?

i want to know about identification of XRD results that each pick positions. as a result of qualitative and quantitative analysis revealed O, Na, Mg, Al,Si, S, K, Fe, Cu, Zn etc.. personally, i...

07 August 2017 2,394 3 View

Identification of XRD results for synthetic jarosite?

anyone who help me about XRD results for synthetic jarosite? i synthesized K-NH4-jarosite mineral under the 90℃ (120h) using morey-type reaction container, and approximately 300mg of the...

07 August 2017 3,476 5 View

Anyone who tell me about the condition of silica gel dissolution by pH transition using reagnet in room temperature

i want to make a homogeneous state for mixing materials (i.c. silica gel powder(Na4SiO4), Al2O3 (l), Fe-sulfate powder, Mg-acetate powder etc.. ) in room temperature. just i used KOH solution to...

04 May 2017 5,056 0 View

XRD results for synthesized smectite, about analysis technique?

i tried synthesis of smectite, and it was measured by XRD. however, too initial intensity is so high to do not show the other peak such (001), or (02-11) reflections. how can i control such high...

01 February 2017 4,427 2 View

About EPMA data; (WDS only), for smectite.?

i analyzed for smectite (i.e. montmorillonite or saponite) by XRD, but sometimes it is difficult to be sure that between saponite and Fe contained montmorillonite at (060) peak position. so that...

31 December 2016 1,991 1 View

I want to know about the formation of NH4(gas or aq) from the combination N2 gas with H2gas; below the conditions?

i want to know about the formation of NH4(gas or aq) from the combination N2 gas with H2gas; below the conditions. just i think that N2 gas derived from magma reservoir, but the production...

10 November 2016 751 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View