Would you please, can any body help me to know the method of save only geometry of model in ANSYS apdl ?

More Alshaymaa Khalil's questions See All

Can anyone suggest me a list of journals in computer science discipline those go for rapid publication (monthly issue actually)?

I would like to publish some articles rapidly. It would be so nice if you suggest me a list of journals those publishes monthly usually. Thanks in advance.

30 December 2020 4,648 1 View

What is the significance of H-Index and Eigenfactor in assessing the quality of a journal?

Its getting tough now a days to successfully assess the quality of a journal. H-Index and Eigenfactor are two such parameters used frequently to determine the quality of a journal. I would like...

29 December 2020 9,032 1 View

Is there a way to isolate nuclei without purifying cytoplasmic protein aggregates?

Hello, I am trying to isolate nuclei from HEK293T cells expressing a protein that aggregates in the cytoplasm, however when I run my samples in western blot the cytoplasmic protein is strongly...

02 November 2020 9,541 3 View

How do I run a western blot following co-ip?

This is the first time I do any sort of IP experiment and I was wondering if there is a certain procedure to follow for the western blot after the last elution step in the co-ip protocol. I am...

22 September 2020 3,688 3 View

Is there any complete documentation for HTM (Hierarchical Temporal Memory)?

Currently, I am working on implementing HTM for some of state of the arts problems. I am facing some issues actually. A complete documentation may help I think.

17 September 2020 8,875 1 View

How to solve fog coating of glass substrate?

I'm coating metal complex on the glass substrate by using drop-casting and evaporate the solvent "DMF" on the hot plate. The glass-coated was transparent, but when the last drop of the solvent...

22 August 2020 3,616 10 View

Can someone help me find a particular article online?

Hello, I don't have access to the below article. Can anyone share it with me? Title: A Matrix Approach to Literature Reviews Authors: Salipante, Paul, William Notz, and John Bigelow Journal:...

06 August 2020 8,095 4 View

Anyone please can tell me how can I simulate carbon fibre composite plate bonded to web in simply supported steel beam by using ANSYS Apdl?

I want to simulate the CFRP plate by using ANSYS classic APDL not by using ANSYS workbench. Please help me if you have any suggestion. I used CONTA 173 associated with TARGET 170 elements as a...

04 April 2020 4,977 3 View

Why does my LCR get different readings when using different fixtures?

Dear all, I have a problem: When i measure my sample using the -Keysight 16451B Dielectric material test fixture-, the measurements (i.e the impedance outputs) are larger than the impedance...

22 March 2020 1,482 11 View

Are exergy and exergoeconomic analysis actually used in industries and their R&D departments ? Are there engineers paid to perform such analysis ?

I am wondering whether exergy analysis is really used within a commercial/industrial framework either to develop or to analyse a product or a process.

24 February 2020 7,346 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

Masud Rana

You can do it this way:

Preprocessor> Archive model> write> select SOLID and save in .igs format

Chitaranjan Pany

try as rana directed

Ahmed Derradji Aouat

An easier way in APDL is to save nodes and element in ASCI text file. Later on, when needed, just read the ASCI file. Using IGS convertors is tricky if the CAD is not stitched together!!!