Following is XRD of iron oxide nano material synthesised using bipyridine derivatives. What are the reasons for Broad Humps?

Even after few repetitions..I am getting similar results. Is is due to organic components?

20 January 2021 9,279 6 View

What are the advantages and limitations of SBF modeling for biological entities?

Researchers from Georgia Tech have developed SBF models to represent biological mechanism. What are advantages and disadvantages of developing and using these SBF models?

29 December 2020 5,098 2 View

How to calculate all the parameter of drug permeation and drug depostion studies in skin?

Drug permeation through mouse skin Drug deposition in mouse skin Steady-state permeation rate Flux Permeability coefficient Diffusion coefficient Lag time.

10 December 2020 3,808 1 View

What are the parameters which determine the potential window of an electrolyte?

Aqueous electrolyte have a potential window of 1.2V, while organic and ionic electrolytes have higher potential windows. But what parameter is contributing to this enhancement in the respective...

19 October 2020 2,447 3 View

How do I give glucose supplements to rabbits after Alloxan intra-peritoneal dose to prevent hypoglycemic shock?

Its study for alloxan-induced diabetes in the rabbit.

14 July 2020 2,869 1 View

A public health crisis, over the coronavirus, has landed right in the nation at the fulcrum of global commerce?

Give your opnion on said question please.

09 April 2020 1,558 4 View

In finite element study on dental implants,is it necessary to find maximum and minimum principal stress or von Mises stress anslysis is good enough?

What are the stress evaluation required for a FEA study on dental implants

09 February 2020 4,382 2 View

How i can use QuiP methodology for qualitative impact assessment ?

I want to use QuiP for impact assessment, what is the process for applying this and in which situation

16 January 2020 314 3 View

How to measure the force in spring/damper of suspension system of train experimentally?

What type of force sensors can be used?

08 January 2020 4,098 1 View

What are some positive control medicine used in diabetic wound in rabbit model?

Alloxan induced diabetes in the rabbit experiment to perform wound-healing experiments.

21 December 2019 2,724 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

How to extract the y+ value from fluent ?

I am doing a 3D steady simulation of a wind rotor using Ansys Fluent. In order to have a y+ of 1, I created 10 inflation layers using total layer thickness method, and I started a first...

23 February 2021 2,819 3 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

How do I add a udf to Ansys fluent and does it need to be compiled before hand ?

I have a Define_CG_Motion udf written in c where do I add it to my Ansys fluent project and does it need to be compiled before that?

21 February 2021 9,347 3 View

How do I plot Pressure against crank angle degree in Fluent?

18 February 2021 8,390 3 View