I am not getting blast pressure value for 15m stand off distance using ABAQUS software. It is showing zero blast pressure. But journal results shows some value using SAP 2000 software.
Because the two programs were different in this solution sap was not near to abaqusth suitable program Ansys program to compare with abaqus
The suitable distance to get blast is 50 m
I am looking for ways teaching specifically science teaching can be improved by using visualisers in classroom .This should to help student to understand clearly ,avoid any misconceptions and...
27 January 2024 1,190 4 View
I have been optmising Si atom (lattice constant), but I am facing an issue with defining an accurate PAO basis block or/and the Eshift!!! I did look through some websites but with the data for...
29 January 2023 6,490 2 View
Please suggest some papers also
11 May 2020 2,913 0 View
I'm working with questionnaire survey data which has multiple choice questions - all categorical (e.g. What beverages do you consume - tea, coffee, something else etc.). Responses from each...
11 May 2020 1,378 0 View
I want to know on what basis a suitable abrasive is chosen in Magneto Rheological Finishing process. For example, if One wants to polish metal surface what type of abrasive is used? For finishing...
05 May 2019 7,561 1 View
I've been working on how rabies has been historically viewed in colonial-era and pre-independence India, and would like to submit my findings to a journal. I find that there's a lot to be gained...
09 March 2019 5,509 8 View
I am going to use a 50 ml teflon lined autoclave for doing hydrothermal synthesis and I am deeply concerned about its safety. The pressure limit inside the autoclave is 3MPa and temperature...
14 February 2018 7,470 3 View
I want to know how much amount of sample we can obtain via hydrothermal synthesis method (in general) using 50ml Teflon lined autoclave?
29 January 2018 4,903 3 View
In XRD pattern of my sample the intensity of my largest peak is less and because of that i am facing problems in Rietveld refinement using Fullprof. Especially in fixing the scaling factor. My...
18 July 2017 6,367 15 View
Hello everyone,. I am new in CFX. I simulated horizontal axis wind turbine through MRF approach. Rotating domain with turbine blade kept inside stationary domain.Boundary conditions;stationary :...
07 February 2016 3,658 3 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,829 4 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,027 0 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,524 4 View
Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...
06 August 2024 977 1 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 452 3 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,061 1 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,571 3 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
Hi Everyone, I'm using an siRNA kit to knock down a target gene. The kit guarantees that the negative control doesn't target any sequence in mouse genome, and when I use BLAST I don't find any...
23 July 2024 2,672 6 View
Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...
21 July 2024 1,680 2 View