How to define the sink temperature and film coefficient?

Hi, everyone. I am considering the heat conviction during compacting simulation by Abaqus. I was wondering that how to define the sink temperature and film coefficient? Is there any references...

21 February 2021 6,197 1 View

Can RNAscope be used to quantify the mRNA expression level of certain genes?

Hello, all, I want to explore the mRNA expression level of certain genes in the brain under physiological and pathological conditions. In previous studies, the researchers usually isolated the...

18 February 2021 1,518 1 View

How to define thermal failure in Abaqus?

Hi, everyone, I am simulate the impacting CFRP model, I want to know how to define thermal failure during the impact process because epoxy degraded owing to thermal effects. Thank you so much for...

25 December 2020 7,424 3 View

How to define thermal conductance in Abqsus?

25 December 2020 3,596 1 View

ESA Eureca spacecraft Solar Array Arcing demage, What is the cause of the problem?

We see a photos of solar array damage suffered by the ESA Eureca spacecraft that was recovered by the Space Shuttle. photo shows a sustained arc site on its solar arrays. In this case, the...

23 December 2020 2,512 2 View

Micro-scale unit in Abaqus?

Micro-scale unit in Abaqus. Hi everyone, I am working on micro-scale simulations, the length of the model is micrometers. So, some information is provided on the internet, but some part is...

10 December 2020 8,448 3 View

How to reduce background noise when testing cholesterol level in rat serum?

l've got rat serum samples with different background (from pink to yellow) and l'm trying to test total cholesterol, HDL and triglyceride in mice serum. l'm worried that the background noise...

14 November 2020 6,628 3 View

Is Uniform Convergence property contradictory to No Free Lunch Theorem?

In Statistical Learning Theory, Uniform convergence means for a hypothesis class H, given m(\delta, \epsilon), for arbitrary distribution over domain (X, Y), with probability $1- \delta$, the...

03 November 2020 7,732 5 View

How to recognize and verify the crystallization occur or not?

Hi, everyone My feedstock powder is water atomized Sn with a diameter range from 10-100 um. After the cold spray processing, the EBSD maps can be obtained. Because my smallest powder is 10um,...

07 September 2020 7,766 4 View

What is we need for Sequence learning (Speech, NLP, Finance, Transportation and so on)?

In 2017, a famous paper proposes Transformer which successfully adopt self attention as well as FFN for NLP. The paper is called "Attention is All You Need". This work lets many scholars know RNN...

11 August 2020 8,119 11 View

How do I increase the yield of my PCR product?

Hello, We would like to increase the yield of our PCR product. We are running a series of PCR reactions that is targeting ~1.1kb sequence. We begin each reaction with ~400pg of template DNA...

02 March 2021 4,029 3 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to determine solutionizing time for cast Al alloys?

For wrought alloys soaking time at solutionizing temperature is determined by thickness .Do we have such standards for cast Al alloys

23 February 2021 8,839 3 View

Which thermal conductivity test recommended for Ag-Cu nanofluid?

I have prepared Ag-Cu alloy with polymer coating upon it.... how can I measure thermal conductivity of it ?

22 February 2021 5,915 3 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

What are damage parameters for SMA while modelling on ABAQUS 2020?

I have given Elastic and Superelastic material properties, but I think we need to provide the damage parameters also. Please help me here.

16 February 2021 8,694 1 View

Are there alternatives to the Devarda alloy when estimating nitrogen?

Are there alternatives to the Devarda alloy when estimating nitrogen? devarda alloy is reducing the nitrate to ammonium

15 February 2021 8,838 3 View

Passivation of chromium cast Iron in high temperature?

14 February 2021 2,157 3 View