Why my Stress-Strain curve in Abaqus oscillate?

More Shahid Ahmad's questions See All

Does anyone use antinuclear antibody (ANA) and anti-Phospholipid antibody ELISA kit for Non Human Primate serum samples?

I am looking for anti-nuclear antibody (ANA) and anti-Phospholipid antibody ELISA kit for Non Human Primate serum samples. Any suggestions highly appreciated. Thank you.

28 February 2021 6,512 3 View

Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

Treating Intermediate Variable in Linear Regression Analysis in SPSS?

While performing the Linear regression analysis in SPSS version 26.0.0. my intermediate/mediation variable goes to the excluded section. Please share your valuable suggestion "How to restrain the...

25 February 2021 4,591 5 View

Why tick's salivary gland extract didn't run in the gel (SDS PAGE )??

Greetings, I want to make SDS PAGE for my sample (Tick salivery gland extract), I tried concentrations 10%, 12%. I also tried high molecular weight ladder. But the protein stopped at the top and...

25 February 2021 7,698 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

How to measure the pH of Peat Soil?

Peat possess organic content above 75% and is highly acidic in nature (i.e. pH < 4). Before commencing stabilization, it is mandatory to know about the pH level of peat. Therefore, your...

18 February 2021 9,424 7 View

How is Initial GDP measured ?

Dear All, I am working on estimating Debt-Growth Threshold but confused about some points. My questions are; - How do we calculate initial GDP Per Capita? Shall we do it in STATA or excel file?...

15 February 2021 2,677 2 View

How to Measure Consumer Willingness To Change from petroleum-fueled vehicle to electric vehicle?

I wanted to calculate the probability of one consumer shifting from using a petroleum-fueled vehicle to an electric vehicle. Since my background is in engineering I do not know much about how to...

15 February 2021 9,190 5 View

Having trouble mounting the sections on the slides for IHC staining, what solution should I use?

Hello everyone, I just started learning IHC staining and I have some frozen sections to practice with in a 96-well plate. I'm having trouble mounting the sections on the slide, a colleague told me...

08 February 2021 6,880 3 View

How to use Image Lab to take an image for the bands and the ladder in the same image merged together in Western Blot?

Hello everyone. I was trying to use Image Lab software to take an image of both the ladder and the samples merged together in one image to see the position of the bands according to the ladder MW,...

04 February 2021 9,996 2 View

How does Scientist/RG community evaluates a case study article and the impact of it on a researcher career?

An article that is published as a case study in the SJR listed journal. How much value is added to a researcher career? How it is evaluated by a scientific researcher/University admission...

02 March 2021 9,661 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

Engr. Tufail

Shahid Ahmad, Providing a useful response would be impossible without the inclusion of geometry data, loading specifications, and meshing details.

Victor J. Аdlucky

The stress vs time and strain vs time curves are oscillating, but if they will be combined (Tools>XY Data>Create...>Operate on XY data: Operators - combine(X,X)), the resulting stress vs strain curve should be linear.