Why my composite can not show any result or outcome when i choose the plot contours on deformed shape function?

04 April 2016 1 3K Report

Why my composite can not show any result or outcome when i choose the plot contours on deformed shape function? Is it because I didn't select the misses stress in the history output field request?

Mahsa Jahani

You should define parameters or results, that you need, in step> field output request.

Badges
Science topic

More Tan Jun Kang's questions See All

Why my maximum Von mises stress of glass composite is higher than carbon composite?

All the data are same accept the material properties are different. But the result show the glass composite has higher vonmises stress than carbon composite. Is it possible?Because carbon has the...

04 May 2016 9,838 2 View

The mechanical properties of GFRP that is use to do the tensile test in abaqus?

what is the value of mechanical properties like E1, E2, V12, G12, G23, density and so on for a GFRP panel in abaqus to do the tensile test.Thanks a lot

03 April 2016 9,526 1 View

Anyone can share with me the example or step about how to model and design a FRP composite by using Abaqus?

I need to using the Abaqus software to create a GFRP composite.Unfortunately, this software i dint learn before.So can someone who is wiling to share some example or step about how to create a FRP...

02 March 2016 4,987 1 View

Anyone can share with me the example or step about model and design a FRP composite by using Abaqus?

I need to using the Abaqus software to create a GFRP composite.Unfortunately, this software i dint learn before.So can someone who is wiling to share some example or step about the create a FRP...

02 March 2016 1,128 6 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View

Abaqus 2023 - How to know how many elements have been deleted during a simulation ?

Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...

17 July 2024 1,501 1 View

How to cacualte the creep life of polycrystal with CPFEM?

I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...

16 July 2024 8,436 0 View