For Catechol catalyzation reaction by the metal complex catalyst
https://pubs.acs.org/doi/abs/10.1021/ic00027a012
Le Chatelier's principle:
https://de.wikipedia.org/wiki/1,2-Benzochinon#/media/Datei:Pyrocatechol_o-Benzoquinone.svg
@Yahia Z Hamada, You would please give the specific reference. That will be more helpful for me. Thanks and regards
Mr. S. Sarkar,
Follow T. H. Al-Noor's suggested reference.
I have the following equation, Eating choice (Yes/No)~ Box type (A/B/C). So the question is whether a certain box type affects eating choice in groups of dogs. The eating choice of each member in...
10 February 2021 6,024 9 View
what kind of test can I do for testing the level of knowledge about their daily operation?
03 February 2021 7,583 10 View
The observed bandgaps are 3.8 eV and 3.4 eV for spin-coated and electrospun films, respectively. What are the possible reasons?
08 January 2021 5,646 6 View
I want to know the reaction mechanism of monoethanol amine used as flocculating agent for rerefining used lubricating oil. Here I have attached one research paper where MEA (monoethanolamine) is...
01 January 2021 5,681 2 View
18 December 2020 4,559 6 View
I am a junior research fellow in the department of Chemical Engineering, Nit Durgapur. I want to know that how can I determine various metal such as Fe, Cr, Mg, Mn, Pb concentration present in...
15 December 2020 9,887 3 View
In O 1s spectra, usually the peak near 531 eV belongs to oxygen vacancy sites in oxides, however, in silicates, these peaks are often reported to originate from O-Si. I am confused if the intense...
10 December 2020 9,496 2 View
Hi, I am trying to find out the mol. weight of GFP 11 because it is tagged to my protein of interest which is 17kDa. GFP 11 has been tagged with my protein of interest while GFP 1-10 is tagged...
09 December 2020 1,863 1 View
I have Fluorescent Polystyrene beads. I need to graft PEG on the surface of it. I am looking for a protocol to do that. Also need to know which experiment to perform to be sure about the grating.
01 December 2020 7,860 1 View
I am conducting a regression discontinuity design where the dependent variable is continuous while control variables are categorical (except the treatment variable). In the usual regression...
01 December 2020 583 3 View
I want to polymerize TEOS on a surface. I know that NH4OH is a preferred catalyst and an alcoholic solvent should be used .But I can not find certain amounts of each material to use. Does any one...
02 March 2021 1,404 6 View
We have synthesized various metal complexes with different environment around the metals. Now to see the application of synthesized complexes we need this study also. we are also interested in...
01 March 2021 1,899 2 View
Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...
01 March 2021 1,907 3 View
Hi, I am running a size exclusion chromatography experiment with a buffer containing Potassium Acetate as a salt. I analyse these fractions through SDS-PAGE. After boiling my SEC fractions in...
01 March 2021 2,622 3 View
How would define the "good" and "poor" distribution of particles within the matrix. Is there a quantitative solution to assess the distribution of the particles, which then having denotation of...
28 February 2021 7,397 8 View
I would like to synthesize a transition metal doped TiO2 via solgel method. Hence, I would like to know which metal salt precursor to choose among Chloride, Nitrate, and Sulphate. A clear...
27 February 2021 4,285 3 View
I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....
24 February 2021 4,428 3 View
24 February 2021 9,166 3 View
Hello, I am trying to make anode for Na-ion batteries. I have no experience with preparation of the electrolyte for any batteries. NaClO4 salt are available and I am planning to use EC:PC as...
21 February 2021 8,132 1 View
Hi all, I am currently working on some background calculations before I start a new project related to metal matrix particulate composites. I am trying to find a way to calculate the stress at...
19 February 2021 8,503 3 View