VIF very high, but correlation is low and coefficient is significant. Which one whould I choose?

Hello. I have a question whether if my coefficients (statistically significant) would be valid when VIFs are really high. In my model, there are independent variables(IV), moderating variables...

26 February 2021 956 13 View

How to clean up TEM grid with plasma cleaner?

I need to clean the hydrocarbon contamination on the carbon substrate of TEM grid. However, I heard that substrate could be broken by the powerful plasma. My substrate is pure carbon, with ~3nm,...

23 February 2021 3,262 5 View

Sb2Te3 thin film annealing and damage(break)?

21 January 2021 9,642 2 View

When comparing two very similar surveys taken over time, but with different sample size, what would be the best way to approach this problem?

Hi, I'm currently analysing a survey for a university course design, and some guidance would be very much appreciated. The students who are enrolled in a (year-long) course were given a link to...

08 December 2020 6,624 9 View

When analysing survey using Likert scale, is it okay to use Friedman's test?

Hi, I'm currently analysing a survey for a university course design, and some guidance would be very much appreciated. The students who are enrolled in a course were given a link to participate...

06 December 2020 6,060 2 View

Which time-serie model is good when using concatenate data?

I would like to make a model using sequence datasets. As I've searched that , many LSTM, RNN tutorials use long-sequential data such as weather in 1950-2020. However, my datasets are short...

24 November 2020 808 3 View

Could you answer some basic questions on CRISPR-cas9?

Hi, I would like to ask simple some questions related to CRISPR-Cas9 that I could not understand by reading some basic articles on it. I am not in that scientific field so my questions might be...

21 October 2020 2,439 2 View

How can I design resin column for test?

I'm interested in the research field of ion exchange resin. I want design about resin column with acryl for test. How do you usually design the diameter and length of small columns for test? I...

13 October 2020 3,443 2 View

How do you check the locations of brain-implanted cannulas?

Hello. I implanted single cannulas bilaterally into the brains of mice to infuse drugs. After behavior tests, what would be the simplese way to validate if the cannulas are in the target areas?...

18 September 2020 8,457 3 View

Why this HPLC data show negative peak?

Lysine was dissolved in mobile phase and injected in HPLC but there are two peaks. One for positive at 2.1 min and another for negative at 2.8 min? Contents of moilbe phase are ACN:Water:TFA =...

08 July 2020 2,695 13 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How to improve the adhesion between germanium and silicon monoxide thin film layers using EBEAM evaporation?

I want to deposit multilayer coating of germanium and silicon monoxide on silicon wafer using ebeam evaporation?

21 February 2021 2,141 3 View