How we control humidity in gas sensor?

Is humidity introduce when Ar/N2 is used as carrier gas in gas sensor?

05 June 2017 9,630 0 View

Please suggest me supplier or labs where i get CNTs/Si junctions based substrate?

02 March 2017 4,466 0 View

Can anyone guide me about air brush technique to deposit the film of CNTs?

Which type of gun/air brush required for this?

09 October 2016 4,877 5 View

Can anyone tell me, which solvent is required for CNTs thin film deposition by spin coater?

Generally, CNTs has poor adhesion on Si wafer, when deposit their thin filmby spin coater. So, I need a solvent that help in good adhesion of CNTs by spin coater...

09 October 2016 6,297 7 View

Can anyone suggest me, order of defect density in case of Graphene using Raman Spectrum?

In my case it comes 5e19cm-2... its very large as compared to reported values....

08 September 2016 4,531 0 View

Can anyone suggest me, how we calculate electrical band gap of CNTs?

Any appropriate technique specially for MWCNTs?

07 August 2016 2,499 2 View

Can anyone suggest me approximately value of electrical current in CNT/Pani Compoites?

with concentration of CNTs in polymer?

07 August 2016 9,405 3 View

Can any one suggest me, which type of sensors used to detect amount of, Chlorine, chloramine, Pb, VOC in water?

05 June 2016 2,330 2 View

Can any tell me, why resistance decrease as temperatures increase in case of MWCNTs?

generally, MWCNTs behave as semiconductor at room temperature.. in my case at room temperature, its i-v is perfect ohmic, but when we record i-v with temperatures.. i found that its resistance is...

04 May 2016 4,421 9 View

Can any one tell me, why electrical current is improved by the addition of CNTs in polymer matrix?

04 May 2016 9,886 0 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

Why initial concentration of Pb not the same as calculated one when testing using AAS?

I am currently doing research on the adsorption of heavy metal using magnetic reduce graphene oxide. I use AAS to determine the concentration of the heavy metal. I prepare the Pb solution with...

26 February 2021 9,580 4 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

CGA 300 Regulator for CO2 cylinder?

Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...

25 February 2021 3,292 3 View