How we control humidity in gas sensor?

Is humidity introduce when Ar/N2 is used as carrier gas in gas sensor?

05 June 2017 9,630 0 View

Please suggest me supplier or labs where i get CNTs/Si junctions based substrate?

02 March 2017 4,466 0 View

Can anyone guide me about air brush technique to deposit the film of CNTs?

Which type of gun/air brush required for this?

09 October 2016 4,877 5 View

Can anyone tell me, which solvent is required for CNTs thin film deposition by spin coater?

Generally, CNTs has poor adhesion on Si wafer, when deposit their thin filmby spin coater. So, I need a solvent that help in good adhesion of CNTs by spin coater...

09 October 2016 6,297 7 View

Can anyone suggest me, order of defect density in case of Graphene using Raman Spectrum?

In my case it comes 5e19cm-2... its very large as compared to reported values....

08 September 2016 4,531 0 View

Can anyone suggest me, how we calculate electrical band gap of CNTs?

Any appropriate technique specially for MWCNTs?

07 August 2016 2,499 2 View

Can any one suggest me, which type of sensors used to detect amount of, Chlorine, chloramine, Pb, VOC in water?

05 June 2016 2,330 2 View

Can any tell me, why resistance decrease as temperatures increase in case of MWCNTs?

generally, MWCNTs behave as semiconductor at room temperature.. in my case at room temperature, its i-v is perfect ohmic, but when we record i-v with temperatures.. i found that its resistance is...

04 May 2016 4,421 9 View

Can any one tell me, why electrical current is improved by the addition of CNTs in polymer matrix?

04 May 2016 9,886 0 View

Can any one tell me, can we use Ar MFC for ethanol sensing?

If yes, what about calibration?

03 April 2016 228 2 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

How do I determine the degree of polymerization of PEG 400 based on NMR integration?

Hello, I am working on the photocatalytic degradation of PEG 400. I would like to know if it's possible to determine the degree on polymerization based on NMR integration, or by the MW of the...

02 March 2021 6,186 3 View

How to polymerize TEOS?

I want to polymerize TEOS on a surface. I know that NH4OH is a preferred catalyst and an alcoholic solvent should be used .But I can not find certain amounts of each material to use. Does any one...

02 March 2021 1,404 6 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View