Dear researchers,
Why do scientists use temperatures between 60 to 70 C to dissolve PVDF in DMF or DMAc for membrane fabrication?
Why do not we use a temperature of 90 C to dissolve it in a shorter time?
Regards
Dear researchers, It is clear that BSA protein is the most common solute for membrane performance examination. However, there is no reference to check the MWCO of the membranes based on BSA...
29 April 2020 6,148 3 View
Dear researchers, The mentioned solvents are organic solvents and it is thought that they can dissolve the oils. If they are not capable to do this, what is the reason? Regards DMAc:...
25 February 2020 140 2 View
Hello everyone I am currently trying to calculate phase lock value for my EEG data with the help of the HERMES toolbox in Matlab. I have a total of 48 subjects with different channel location...
04 January 2020 5,220 1 View
Dear researcher, We all use the non-solvent additives to improve the structure and performance of the polymeric membranes. However, the non-solvent additives can be easily washed out quickly with...
29 December 2019 5,366 1 View
Dear researchers, I want to put my SEM photos together to have a picture like the attached photos for my article. Could you please guide me what is the software that I can use? Regards
16 December 2019 4,165 12 View
Dear researchers, I want to determine the estrogen hormone concentration in water. Where is the special laboratory to do this in Iran? Could you please guide me? Best regards
11 December 2019 2,829 2 View
Dear researchers, There are some white bubbles on the surface of the SEM micrographs. What are these particles? Kind regards Foroogh
25 November 2019 5,365 3 View
It is reported that PES/DMSO membranes are too brittle. Is there any method or additive to make them more flexible? Regards
18 October 2019 1,576 6 View
Dear researchers, The surfactants are extracted from the nature are more useful. Can any one introduce an available cheap (herbal) surfactant to produce water/oil emulsion? Thank you so much....
08 March 2019 4,539 7 View
Dear Researchers, I need a 3D photo of a porous material such as attached one only to show the porosity, not for analyzing porous materials. Can any one help me? Regards Foroogh
19 October 2018 7,403 6 View
What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?
28 February 2021 6,516 5 View
I am trying to calculate the theoretical density of my ceramics materials. I use the formula below to calculate the theoretical density: Theoretical density = (Molecular weight x No. of molecules...
24 February 2021 3,823 2 View
I am currently trying to stain for PI3KBeta in MDA-MB-231 cells. My current issue is that 1) beta stains all over the cell and 2) there is an increase in signal at the edge of the cell and this...
24 February 2021 8,582 1 View
Hi everyone! I try to detect VDR protein (~48 kDa) using Western Blot. After SDS-PAGE using 10% MP TGX Stain-Free Gel from BioRad I transferred the protein onto an metOH activated PVDF membrane...
23 February 2021 6,266 3 View
what is the reason film thickness increased when increased doping concentrations give some reasons The measured film thickness is 156, 282, 394, 548 and 681 nm for 0, 1.5, 2.5, 3.5, and 4.5 wt....
17 February 2021 8,987 5 View
I have been reading various articles and most state that treatment with CaCl2 produces higher efficiency of transformation than MgCl2. Can anyone explain why Ca2+ is better than Mg2+ at...
16 February 2021 8,519 5 View
I am working on modeling of Direct Contact Membrane Distillation system with COMSOL Multiphysics software. I have some problems with the mass transfer part of the simulation because I don't know...
14 February 2021 379 2 View
This is a follow-up on an earlier question regarding mechanistics of vaccines: why current vaccines don't block transmission. In summary, they don't engage mucosal immune cells to produce IgA....
08 February 2021 8,321 3 View
Do you know why my membrane looks like this? I did this western for Anti-hnRNP D/AUF1 antibody ab50692, as primary antibody in 1:1000 overnight at 4c and Anti-rabbit IgG HRP linked antibody...
07 February 2021 5,591 4 View
Hey, I want to know if I have fabricated some nanostructure and further I want to make a shell on the nanostructure by solution phase method by making it core-shell nanostructure. So, anybody can...
01 February 2021 9,966 4 View