Why and When should Cytosine(C) or Tymidine(T) in Probe sequence modify to pdC and pdU in probe synthesis respectively ?

12 December 2018 0 4K Report

Hello

I wanted to know why and when should Cytosine(C) or Tymidine (T) in Probe sequence change to pdC and pdU in probe synthesis ? and does this modification could occur in primers too?

Thank you

Badges
Science method

More Forough Tavakoli's questions See All

What is the best protocole of Nasopharynx swabs RNA extraction by trizol for transcript quantification?

Hello all. I would be grateful if I could use valuable comments from anybody who has experience in this field. my nasopharynx swabs are not fresh. they have collected and immediately frozen at -70...

11 December 2019 2,421 3 View

I can't see the ssDNA band after performing asymmetric PCR. Is there any way to do this?

After performing symmetric PCR, PCR purification was performed. Afterwards, asymmetric PCR was performed using the PCR purification product as a template, but no ssDNA band was confirmed in the...

08 August 2024 1,668 3 View

Why after performing site directed mutagenesis ,I don't see any colony after transformation?

I want to introduce a point mutation (change in one nucleotide) into my gene of interest (DNA binding domain) I have designed primers as recommended on the Data sheet of the kit : -Both primers...

05 August 2024 9,059 3 View

Anyone having idea about VN primer for miRNA primer design ?

How to design VN primer to attach with universal reverse primer

05 August 2024 2,116 3 View

Z-average size from Dynamic Light scattering can it be lower than the original probe size?

Hi everyone, Recently I have been conducting Dynamic Light scattering experiments in a micellar solution at 5 and gel at 37 degrees of Celsius with latex particles of diameter 190-500 nm. While...

01 August 2024 1,168 4 View

I'm optimizing a tetra-ARMS PCR protocol with amplicon sizes: 165bp, 123bp and 93bp. Why, in the gel, only 165bp is visible while I'm expecting all 3?

It's an end-point PCR protocol. I'm using 1.5% agarose gel with SyBR Safe dye and TBE as a running buffer, visualization on BioRad XR+ system. I was primarily thinking of primer efficiency,...

01 August 2024 4,673 4 View

PCR showing no bands - Master mix and primers didn't mix?

Hello everyone, I performed a PCR yesterday, and the results showed no bands on the gel. Of course, I probably missed some crucial steps, like adding my samples to the PCR strips themselves, for...

31 July 2024 2,406 6 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

How to retain amplicon yield after Ampure bead cleanup, following a 2-stage PCR protocol?

Hello all, I have been trying to follow a 2-stage PCR protocol used to amplify barcodes of a large yeast library, as per Nyugen et al. (2022) -...

30 July 2024 841 2 View

Is it necessary to attach fluorophore at 3' end in MIC RT PCR machine for Dual hybridization Probe designed especially for genotyping assay?

I designed 2 dual hybridization probes for my single SNP. where I attach my fluorophore 5'-FAM-nnnn-BHQ1-3', and 5'-HEX-nnnnnn-BHQ2-3'. I need to run it on the MIC RT PCR machine by Biomolecular...

28 July 2024 5,658 0 View

Do you mix and add all primers together in a singel PCR reaction (4 total primers for 2 mutations) when using Agilent's multi-site mutagenesis kit?

I want to introduce 2 mutations using Agilent's multi-site mutagenesis kit, I designed the primers using their online tool and it gave me 2 sets for primers (1 set for each mutation) so I was...

25 July 2024 6,517 3 View