I would appreciate some insights.
Yeah, I have been asking students to work on such problems for fun, but I did not get feedbacks.
Hi Houman, we have some experience even using SAP or Cast3m making use of nonlinear material models.
Take a look at this article:
http://www.palgrave-journals.com/jba/journal/v5/n2/full/jba200924a.html
If you have any problem just ask me.
Regards
If you are interested in masonry chimneys, I can send a few references on modeling masonry.
Thanks I work at concrete chimney
I want to model the moving mass (not vehicle) in sap 2000, Can anyone help me?
09 October 2014 6,452 5 View
I want to calculate the response of soil from acceleration in bed rock with matlab. I programming this with Matlab, in linear manner and attached. I want to programming with equal linear and...
07 August 2014 7,168 4 View
I have a model of tall concrete chimney in Abaqus but it has error. I try to correct it but not possible. also I want to meshed it like attached picture. Can anyone help me? My analyses is...
05 June 2014 3,345 9 View
I calculated FFT of response and force with Matlab code. And then I divided FFT response to FFT force and calculated FRF. This is for sdof. But I don't have true results.
31 December 2013 7,556 13 View
Matlab code.
31 December 2013 5,474 23 View
I have two signals (response and force) and I want to calculate FRF in MATLAB. And I must calculate it with FFT. but I resulted not good.
31 December 2013 2,865 12 View
The system identification with wavelet method uses response of system against force. Which force is acceptable?
31 December 2013 5,921 6 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...
08 August 2024 6,134 12 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...
03 August 2024 3,371 3 View
I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?
02 August 2024 3,143 4 View
Suppose I am studying the construct of "Academic Motivation" (latent variable) in students, which is measured through three observed variables: "Intrinsic Motivation," "Extrinsic Motivation," and...
31 July 2024 3,913 6 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View