Which thermoplastic polymer exhibits the best adhesion to aluminum?

More Anton Kuzmin's questions See All

In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Unknown debris sheets observed in cell culture flasks?

Hi, We culture neural progenitor cells in T175 culture flasks coated with PLO-Laminin. We have successfully grown these cells with our protocol for months. Recently, we observed large sheets...

25 February 2021 3,443 4 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

Is there a suitable way to confine cell attachment area inside a multi-well plate?

Are there any types of cylindrical cell culture inserts that are designed to confine cell seeding area? Say, if I'm using a 12 well plate (3.5 cm^2/well), but only want to seed cells in the middle...

22 February 2021 7,127 4 View

Is there a method for evaluating nanoparticle adhesion to epithelial tissue in vitro?

I want to measure how well nanoparticles can transfect cells based on NP adhesion properties. In the literature I find people do it in animal studies, and epithelial adhesion helps in transfection...

21 February 2021 7,791 3 View

Is there a way to grow biofilm in lab to mimic biofilms in showers and baths? Also, how can I measure it?

Hello, I am new to biofilm research and have a question about growing and measuring biofilms. We want to research the effect of a type of enzymes in breaking down biofilms in showers, baths, hot...

14 February 2021 3,522 3 View

How to improve the adhesion of epoxy coating on steel substrate? Which factor affects?

I am facing a problem regarding a de-adhesion problem with the coating. A brief description of my methodology is given below. I am using mild or Low Carbon steel as a substrate and I polish the...

14 February 2021 2,167 4 View

Can I use aluminum or copper based substrate for DNA origami imaging using SEM?

As suggested in the title I want to image my DNA nanoflowers/origami using SEM. These nanoparticles are an organic-inorganic particle made out of highly packed DNA and also contain magnesium...

28 January 2021 3,343 3 View

How to know homogeneity of two thermoplastic polymer composite?

I have melt mixed to thermoplastic polymers. But I want to know the homogeneity of the composite. What are the methods to determine whether the composite is homogeneous or not? Please help.

20 January 2021 9,085 5 View

Abdelkader BOUAZIZ

Dear Anton Kuzmin, I suggest any one of the family of polycyanoacrylates. It is to be applied as an adhesive or as a coating? My Regards

No thanks. Cyanoacrylates are good adhesives with simple chemistry, their only drawback is the poor high temperature tenue. Please have a look at the attached files. My Regards

Anton Kuzmin

Yes, I know about cyanoacrylates. This is a very good adhesive. But first I also thought of EVA or maleated polyethylene. I need to compatibilization natural fibers and aluminum plate