11 January 2021 4 6K Report

The melting is done in an free domain so once the metal start to melt, its free to flow (no constraints) and solidify once the heat source is removed.

More Simson D's questions See All
Where to start the Analytical model for Dry sliding wear of metal surface ?

I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.

29 July 2024 6,115 0 View

While doing Chronoamperometry, when the light is turned off, why the current is not decreasing sharply?

Here, I have used Ag/AgCl as reference electrode and 0.5M KOH.

29 July 2024 4,538 3 View

Is it possible to dock more than one drug in the same active site or pocket of a protein to study synergistic/antagonistic/additive properties?

I wanted to know whether we can observe the synergistic/antagonistic/additive properties of combinations or mixtures of compounds through docking analysis. But during docking preparation any...

28 July 2024 7,413 6 View

Validated HPLC method for the estimation of the Amphotericin B ?

During the release test of Amphotericin B using 1% Tween 80, i observed three peaks even in the standard. The first peak consistently yielded results around 500%, while the other peaks showed...

08 July 2024 1,330 0 View

Regarding green consumer behaviour ?

HOW TO WRITE GREEN CONSUMER BEHAVIOUR AS A LITERATURE REVIEW

28 June 2024 2,661 0 View

Can the atomic % and weight% of a doping element decrease with increasing its concentration in the resulting compound? If yes, then how?

I found atomic% and weight % of doping element decreased in the resulting compound on increasing its concentration.

28 May 2024 2,455 2 View

How do I perform a dose response curve and get IC 50 values for herbal extract powder?

I need to find out the desired dose for my poly herbal formulation. Please guide me how to get the figures

12 May 2024 8,290 1 View

CNN model and Multi-output regression?

Dear All, I have an imagery with a single fish species within each image along with a list of morphometric measurements of the fish (length, width, length of tail, etc). I would like to train a...

28 April 2024 2,090 2 View

How to calculate the stress of material using XRD data?

Is there any formula to calculate stress

20 April 2024 8,612 2 View

Any studies/PhD thesis that has taken pan country as the sample and used FGD for studying a public health problem?

The pan-country study could have further divisions/categorization based on different criteria. Any recommendations would be greatly appreciated. Thank you!

27 March 2024 991 1 View

Similar questions and discussions
Can formaldehyd-fixed gelatin be melt?

I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...

07 August 2024 1,686 1 View

Melt curve problem in qPCR?

Do these peaks in the curve indicate primer dimer or non-specific products?

01 August 2024 7,466 0 View

What is the best protocol for freezing the rat brain in preparation for protein detection by Elisa ?

What is the best way to freeze the rat brain - liquid nitrogen, Dry ice , isopentane - after isolation for later protein investigation by Elisa?

01 August 2024 1,722 1 View

How to Post-fix Mice pup's brains?

I need to Postfix mice brains. I slice the brains using microtome at 40 microns. These are Postnatal days 7, 11, 14, and 21. I am using half the brain for other analysis, so I need to fresh freeze...

31 July 2024 1,123 4 View

How to Freeze Embryos for Spatial Transcriptomics?

Hello everyone, I am currently working on a project involving spatial transcriptomics on E14 mouse embryos. We need to perform cryosectioning without fixing the embryos. Here is the protocol we...

10 July 2024 5,985 0 View

Suggestions for storage of CD4+ naive splenocytes for future use?

Hi! I am working on a biophotonics project in which I need isolated but inactive CD4+ splenocytes. Every protocol and piece of literature I have found immediately activates and cultures...

02 July 2024 4,887 0 View

How does the melting point of a spherulite correlate with its size?

For Polybutylene Terephthalate (PBT) it is known that if you cool it down at fast rates to have an additional melting Peak in DSC-Scans. Androsch et al. (2015) conclude that this is due to...

30 June 2024 2,891 1 View

How to reduce the material coming out of the torque rheometer?

A physical mix was in vitro evaluated on a torque rheometer. The composition was predominantly recycled polypropylene (PP), yet the melt flow index (MFI) was found to be excessively high....

25 June 2024 10,154 0 View

Why is my TE-eluted cloned plasmid (isolated via miniprep) not freezing at -20 degree celsius? Is it normal?

I isolated my cloned plasmid from TOP10 cells using invitrogen plasmid miniprep kit and eluted it in TE buffer. But I noticed that contrary to my plasmid aliquot, it does not freeze at -20 degree...

19 June 2024 1,612 8 View

Discuss the potential effects of melting polar ice caps on global sea levels and climate patterns?

Polar ice

12 June 2024 9,997 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close