Regards
AL-5%Ti-1%B
I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...
06 August 2024 1,367 3 View
Information literacy in higher education integration with curricula engineering
04 August 2024 5,368 3 View
Hey! I aim to generate a transgenic knockin zebrafish line that mimetizes a genetic condtition that leads to a certain disease on human. To do so, I need to insert a codon for mutagenic aminoacid...
14 July 2024 6,240 0 View
Please (for Arabidopsis), what could be a good Lumens and color range (Kelvin) range for full spectrum LED lamp tubes size T8 (120cm) for each shelve measuring 130x50 cm (length x width) and 60 cm...
11 July 2024 6,078 1 View
What are the standard applications of Cross Attention in Transformer Architectures ?
09 July 2024 9,310 2 View
Are there standard RNN architectures been applied for Time Series Analysis, forecasting and anomaly detection problems ?
30 June 2024 3,169 8 View
Have we ever used LSTM architectures on Time-Series Forecasting and Analysis, and gotten a decent result ?
30 June 2024 6,924 3 View
I am new to running PCR gels. I loaded this gel and I thought it was fine, meaning I saw/felt no apparent punctures or spillovers to neighboring wells (see picture 1). When the gel started to run,...
30 June 2024 4,107 4 View
Where are large vision models typically used ?
25 June 2024 4,113 0 View
When it comes to Re-inforcement Learning with Human Feedback, are there standard libraries/frameworks for training LLMs ?
25 June 2024 1,121 0 View
Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...
07 August 2024 9,563 0 View
How select composition for ods-high entropy alloys?
31 July 2024 2,795 1 View
Any suggestions with respect to etchant composition and holding time?
27 July 2024 6,925 2 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
How can the rubber fibres produced by the electrospinning device be removed from the fibre collector (aluminium foil) without affecting the orientation of the rubber fibres for use in reinforcing...
26 July 2024 8,281 0 View
I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...
13 July 2024 9,003 2 View
Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...
13 July 2024 2,417 1 View
In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....
11 July 2024 4,476 3 View
Hello everyone reading this topic! It is well known that microcrystalline cellulose 102 is recommended for use in direct compression technology, however, like other grades, it has poor flowability...
08 July 2024 2,807 0 View
I synthesise intermetallic compounds through nickel and aluminium powders. But the pure powder after synthesis is difficult to obtain. Especially the presence of aluminium oxide very seriously...
01 July 2024 4,030 3 View
