How to dissolve carbon coated LiFePO4 in solution/acid for ICP-MS test?

I tried to dissolve in HCL, HNO3 separately and mixture of both with DI Water (HCL:HNO3:H2O=10:10:80 by volume) but LiFePO4 did not dissolve. I also mixed solution by magnetic stirrer overnight...

10 November 2017 2,672 3 View

Why does LiFePO4/C dissolve in LiPF6+EC:DEC electrolyte?

08 September 2017 9,149 10 View

How to calculate warburg factor in nyquist plot during EIS test?

10 November 2016 1,693 0 View

What is the advantages of using carbon coated copper TEM grid over non coated for ceramic powder? What wil be the effect if I use non coated Cu grid?

TEM analysis of Ceramic powder.

01 January 1970 2,432 3 View

Will there any effect on LiFePO4 if heat treatment is done in iron tube?

I am trying to synthesize LiFePO4 but did not get success. I just copy many synthesis methods (by sol-gel and hydrothermal process) from reputed journals, still, i am not getting pure LiFePO4....

01 January 1970 2,185 3 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How does elongation affect the resistance of an electrode?

What are the testing rate for electrodes recommended by ASTM for cochlear implants. I am currently doing the 15mm/min elongatio testing.

22 February 2021 1,515 1 View

How to prepare electrolyte of NaClO4 salt for Na-ion battery? Any problem with this salt?

Hello, I am trying to make anode for Na-ion batteries. I have no experience with preparation of the electrolyte for any batteries. NaClO4 salt are available and I am planning to use EC:PC as...

21 February 2021 8,132 1 View

Is that possible to do an impedance measurement without FRA module?

One of my colleagues said, "the impedance you can measure with the three electrodes and with the specific sequence varying the frequency" Is it possible to configure the potenciostat without the...

21 February 2021 418 2 View

Do you know this error? The experiment was stopped by a potential overload on Vs (auxiliary electrode)?

Hello everyone Do you have any information about this error 'The experiment was stopped by a potential overload on Vs (auxiliary electrode)' in Origamaster software? I tried everything possible,...

19 February 2021 3,152 7 View

Which compound is getting oxidized during bulk electrolysis with TFAA?

The experiment is really simple. When I do a bulk electrolysis with 1% TFAA (ACN solution) to get dihydrogen, what is going to be oxidized? (working electrode graphit, counter electrode platinum,...

18 February 2021 4,430 1 View