How to select from various invitations from Scientific Boards in conferences and proceedings?

How to select from various invitations from Scientific Boards in conferences and proceedings? How to spot the ones with high impact and genuine? Can we spot valuable events?

02 February 2021 8,187 1 View

Can R be used for SEO?

13 January 2021 1,920 1 View

Fish gut microbiota extraction and identification protocol?

Hi, I need a protocol to extract and identify microbiota from fish gut. Any suggestions? Thank you. (P.s. Something low tech as I am technologically limited, guess no funds and big high tech...

01 January 2021 808 1 View

Bisphenol A in water - measuring bpa protocol using a uv/vis spectrophotometer?

Hi, I'm interested in a protocol for measuring concentration of BPA in distilled water (no interference) using a uv/vis spectrophotometer . The method found...

09 November 2020 7,012 3 View

How to remove ethanol from a 95% water solution?

How can ethanol be removed from an azeotropic 95% water 5% ethanol solution, without reaching more than 30 C temp?

06 November 2020 8,718 2 View

Bisphenol A solubility in water protocol?

Upon some research I found different protocols of BPA solubility, some state a 5 v/v % ethanol (MOTOYAMA et al ) will catalyze the process of solubility and BPA will stay in solution (being an...

06 November 2020 8,152 8 View

Proceedings Of International Conference Building Services And Energy Efficiency is Scopus indexed?

Proceedings Of International Conference Building Services And Energy Efficiency is Scopus indexed? see link here https://content.sciendo.com/view/title/580364

05 November 2020 4,157 3 View

Probable Identity table of halophilic bacteria?

I need older protocols that predate pcr, on halophilic or halotolerant bacteria. Looking forward to receiving your answers, thank you.

13 October 2020 8,022 5 View

Is there a valid alternative way to replace the use of camera lucida (or drawing tube) for scientific and taxonomic drawings?

So far I have not been able to find a camera lucida that fits a low range microscope.

05 September 2020 3,342 4 View

What is 'data Interpretation' in the context of an undergraduate dissertation in Management?

Hello, Thank you for taking the time to help. For context I'm a Year in Industry Placement student preparing for, and getting a head start on his third year dissertation. I've encountered a...

12 August 2020 6,903 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View