We are working on nanoparticle systems and conjugation. Kindly suggest who can support by providing free samples of mPEG amine or PLGA-PEG copolymer. Thanks
I cooperated with the University of Ljubljana in a European project in this field.
I would advise you to contact Janko Kos, Matija Rojnik or Petra Kocbek, all members of research gate.
Hello connection While performing potency test by using BD FACS instrument some time we few population inside the gate few outside of gate and some time I got population outside of the gate I am...
17 March 2024 3,511 4 View
Kindly provide the details
30 August 2023 4,884 1 View
I am referring Theoretical studies on electrochemistry of p-aminophenol paper for calculating the theoretical redox potential using the described in this paper. I reproduce the DFT calculations...
18 August 2023 3,573 1 View
I encountered the calculations in the research article titled "Theoretical studies on electrochemistry of p-aminophenol ." However, I'm having difficulty comprehending the procedure used to...
13 August 2023 1,639 1 View
I have a query is that after crystallization peak point some of other noise type peaks occur in DSC scan for (Se78-xTe20Sn2Znx) x=2 and x=6 ,this peak shown the material property or due to...
05 August 2023 8,945 1 View
I am trying to optimize the geometry of a reactant complex obtained from the IRC. The geometry of the product complex is getting optimized, but in the reactant complex, the maximum force is not...
23 May 2023 8,098 3 View
Hello everyone, In my case, i ligated my insert (804 bp) into pET30a expression vector (5422bp) 3:1 ratio containing 20 ul reaction by using T4 DNA ligase and incubated at 24 degree centigrade...
16 May 2023 884 3 View
Hello everyone, I have one doubt regarding cloning ? I am using pET30a (+) vector for cloning (5422bp) and Insert size 804bp. I tried all the ligation reaction ratio lilke 1:3, 1:5, 1;7 (100ng...
26 March 2023 7,023 6 View
Some journal reviewers prefer that the rate performance of batteries be expressed in C rate rather than A/g. However, since battery capacities vary across different chemistries, wouldn't A/g be a...
20 February 2023 973 1 View
This specimen was collected from the intertidal habitat of the Kerala coast, south India.
05 February 2023 2,190 7 View
I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...
30 July 2024 3,294 3 View
For example, if low-density polyethylene (LDPE) is equilibrated with PCB contaminated marine and freshwater sediments, can LDPE-lipid partition coefficients be used to obtain equilibrium...
28 July 2024 263 1 View
Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...
25 July 2024 8,108 0 View
Hi everyone, Can someone explain for me a method to inject VOC collected with Tedlar bag from pyrolysis process and transfer or inject into GCMS. Thanks
22 July 2024 6,398 1 View
I have a mixture of glycol, water, MDEA, and piperazine. I want to analyze it with GC-FID.
15 July 2024 9,652 3 View
I have a mixture of glycol, water, MDEA, and piperazine which I want to analyze with GC.
15 July 2024 2,181 10 View
When polyethylene, whether high-density or low-density, is mixed with percentages of waste tire rubber, it becomes a new material. Where can it be used?
26 June 2024 3,349 2 View
I have a copolymer if epoxy and rubber reinforced with Sic. I want a standard FTIR figure in transmittance mode.
20 June 2024 6,606 2 View
I'm working on the RAFT copolymerization of MPC and NIPAm monomer, but I'm not sure how to calculate the total conversion from proton NMR? Is it an average of conversions of two monomers or just...
10 June 2024 7,430 2 View
I am studying polyethylene heat absorbing systems. For example, modeling heat exchanges in a solar air heater and temperatures for melting polyethylene.
01 June 2024 9,379 7 View