MOS Capacitor instance or a mosfet used as a cap (D-S-B connected to gnd)?

Hi, in Cadence Spectre simulations should I use a MOS cap instance or a mosfet (D-S-B connected to gnd) to simulate a real life MOS-cap? I tried both of them and they gave different results i.e....

26 December 2020 6,407 1 View

Angiotensin peptide stability?

Hello all, We are currently working on angiotensin analysis, however we observed that, once the freeze-dried peptide is dissolved in an aqueous buffer, it gets unstable in only 2-3 hours. Mass...

13 November 2019 787 1 View

Can anyone suggest me how to approach to design a Frequency Hopped OFDM system on Simulink?

The proposed system deals with wideband frequency hopping. The system will be able to hop between three sub-bands, with each sub-carrier having a bandwidth of 40 MHz. The three sub-bands hopping...

08 November 2019 2,574 2 View

How can I isolate mitochondrial DNA from adherent cell lines?

I have tried using the Plasmid isolation Kit as recommended by...

22 October 2019 2,118 6 View

Can microbiology pipettes be used for cell culture?

Hello everyone, We have a multichannel pipette in the microbiology lab that has been used against various pathogenic bacteria. If we want to use it for cell culture, can it be sterilised? If yes,...

08 August 2018 9,873 14 View

Can you suggest me a high electrical conductive material which i can use at 1100 C in H atmosphere

I tried graphite before but i faced ash like wearing problem. I made some research and found Inconel 601 - 617 (Nickel alloy) and TMZ alloy (Molybdenum alloy) which are hard to reach. I will try...

02 August 2017 6,741 3 View

Stress-Strain damping-strain curves for different soil medium?

14 July 2017 6,805 3 View

Does anyone know in - vitro lipolysis test?

I am trying to test lipolysis ability from certain compounds or extracts. I only know adipocyte cell line based assay. Does anyone know chemical-enzyme(chemical) reaction to test lipolysis without...

16 August 2016 4,301 1 View

What is New Next Generation Attenuation Relationships (NNGAR) and how are they different from other attenuation relationships?

Dear researchers The provisions of ASCE 7-10 states that New Next Generation Attenuation Relationships (NNGAR) has been used in the process of Probabilistic Seismic Hazard Analysis (PSHA) to...

15 November 2020 1,132 4 View

Selection of Steel Frame Section in SAP2000?

Hello, I have a technical question about the selection of steel frame sections in the designing of steel frame structure i.e W16x48 etc. The common practice I have seen is the trial and error...

11 November 2020 5,762 4 View

Can anyone please tell how to define link for Tuned mass Dampers using Sap2000/Etabs?

Dear Research scholars, I was doing my MTech thesis on pendulum based TMD and I was having trouble defining the link properties. I even followed the tutorials put on CSI website. still, I wasn't...

11 November 2020 8,309 11 View

Sir can you send me your research paper " Earthquake risk management assessment and evaluation for turkey" in short time?

05 November 2020 10,019 3 View

What is the sense of slip either strike-slip or thrust fault for Turkey earthquake on 30-10-2020?

Dear earthquake experts What is the sense of slip either strike-slip or thrust fault for Turkey earthquake on 30-10-2020? thanks for comments. regards Ijaz image from bbcurdu.com.

29 October 2020 1,890 3 View

Stiffness changes of the structures due to modeling P-Delta effects in Sap2000 are more significant than OpenSees. which is more accurate?

Dear researchers The modeling of P-Delta for the structural elements (specially columns) reduce the stiffness of the structure and consequently increase the period of vibration. Now, these...

24 October 2020 7,255 5 View

No title

Dear All, I'm looking for a freely available software /tool/script for the detection and location of local earthquakes using data from my own network of more than 20 vertical component...

29 September 2020 6,178 8 View

How to invite call centers to participate in your study?

I'm conducting a job satisfaction study to predict telephone agents' turnover. I'm looking to increase participants for my study. How should I approach the directors of call centers to request...

20 September 2020 7,099 8 View

Which is the best Finite Element Analysis software for Geotechnical Engineering?

Dear RG Community, As we are aware that there are almost 5-6 FEM softwares available for modelling and analysis, say, PLAXIS, FLAC, GeoSlope, Abaqus etc. related Geotechnical Engineering. I am...

13 September 2020 3,769 32 View

Does modal participating mass ratio reflect the effectiveness of Tuned Mass Dampers (TMDs)?

Dear researches In general, the value of modal participating mass ratio (MPMR) for each vibration mode represents the participation of each mode in the structural responses. when a structure...

02 September 2020 1,372 9 View