Please help for the above question. How to introduce dopants incase of liquid source of host matrix?
First of all take a certain amount of TTIB which will be in mL (liquid). By using formula of density ( d=m/V) find the mass of TTIB from given volume.
Then find how much mass of TiO2 is produced from total mass of TTIB produced.
Now calculate the percentage mass of dopant as compared to produced TiO2.
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I am excited to announce an opportunity for dedicated researchers to join our dynamic team for an ongoing meta-analysis study. If you are passionate about research and have a keen interest in...
01 August 2024 6,737 1 View
Where can we find freely available data on earthquake fault plane solutions including different parameters such as dip, strike, rake, magnitude ?
05 June 2024 245 0 View
In the SSR method, I used the same pair of primers (forward and reverse) in two different individuals, but I observed different band patterns in PCR.
05 February 2024 3,438 2 View
Genetic Engineering. Assuming that there were no errors during the process.
03 February 2024 2,832 0 View
Genetic Engineering. Sequence. mRNA sequence.
03 February 2024 1,375 2 View
Genetic Engineering. Markers.
03 February 2024 4,012 0 View
Genome library. Restriction Enzymes. Genetic engineering.
03 February 2024 5,429 2 View
This is a topic for research paper: Digitalization of Accounting
04 May 2023 1,394 0 View
Co-contamination of fluoride- arsenic , arsenic-lead are prevalent due to geo-genic issues. Sometimes they are also associated with high iron content in ground water. Is co-contamination behave...
18 May 2022 539 3 View
I need to do some experiment with it in liquid form.
07 August 2024 613 3 View
Global ‘Weather’ has stopped, as ‘aqua thermionic instituted by the ‘Global thermo atmospherics has instituted global thermodynamics of 120º C + and thus all waters are, or have boiled into a...
06 August 2024 8,716 0 View
I am trying to recover liquid CO2 from a mixture of 0.6 CO2, 0.3 N2, and 0.1 O2. My aim is to recover about 99% liquid CO2 at the bottom of the column and make sure the amount of gaseous CO2...
06 August 2024 4,611 0 View
I have prepared a liquid broth containing Yeast (S. Cerevisiae) that i need to add from it to fermentation media of lignocellulosic hydrolysate. I need to know based on what parameters do we add...
06 August 2024 662 1 View
I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.
02 August 2024 6,789 4 View
What is the best way to freeze the rat brain - liquid nitrogen, Dry ice , isopentane - after isolation for later protein investigation by Elisa?
01 August 2024 1,722 1 View
Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...
30 July 2024 3,849 0 View
Hello everyone, I am running DFT with CP2K software at 1200 K, 1 bar with a periodic system of 64 Al atoms + 2 CO2 atoms. However, I am seeing my temperature slowly increase to >4000 K and my...
22 July 2024 3,177 0 View
Can we conduct DFT studies for Ionic Liquids with Amines at various concentrations? If so, how can we proceed with these studies? Additionally, what parameters, besides IR, NMR, and HOMO-LUMO, can...
18 July 2024 319 1 View
what is the relationship b/w TCD signal(a.u) and CO2 desorbed (mmol/g) ? can we plot CO2 desorbed(mmol/g) Vs Time(min) from TPD data?
15 July 2024 3,248 1 View