Where can I get the help regarding the FLUENT simulation of flow Maldistribution in a Micro channel heat sink?

05 May 2017 1 4K Report

Hello, everyone!! I am a Research scholar, I am conducting experiments in the area of flow maldistribution in micro channel heat sink. I also want to perform some CFD-FLUENT based analysis of my work. For the same, i wish to learn some FLUENT based simulation in my current research. Any kind of help regarding the steps involve in CFD analysis of my work will matter a lot.

Regards,

Vikas Kannojiya

Kannan Kaliaperumal

Please register for the workshop you will get expert advise

Dr. K. Kannan +91 9442616597

Badges
Science topic

More Vikas Kannojiya's questions See All

How to work with a stl file obtained through 3D-Slicer?

Hello, I want to simulate the flow through a 3-D domain by using ANSYS Fluent/CFX. The 3-D file is in stl format obtained through 3D-Slicer. I have used MeshMixer to make the 3-D file workable...

09 October 2018 6,379 7 View

How to get start with Immersed Boundary Method?

Hello, I want to analyze the blood flow in artery using Immersed Boundary Method. I am completely new to this method. Can anyone suggest me how to get start with IBM? Which solver should i choose...

31 December 2017 9,067 5 View

How to create 3D geometry from MRI (Magnetic Resonance Imaging)?

I want to create a 3-D geometry by using MRI (Magnetic Resonance Imaging). I want to know that how to transform the data of MRI into a 3-D geometry that can be imported in CFD. I am thankful for...

10 November 2017 4,223 7 View

UDF for moving 3-D wall in FLUENT/CFX?

I want to simulate a 3-d domain whose size varies with time (expansion and contraction), Can any one suggest me UDF for moving mesh for this particular case?

10 November 2017 9,271 10 View

Error in compiling UDF-FLUENT?

Hello, I am having windows 8.1 and visual studio 15. I tried to compile my udf in ANSYS-FLUENT but i got an error "The UDF library you are trying to load (libudf) is not compiled for 3ddp on the...

10 November 2017 4,707 2 View

Where can I get the help regarding the simulation of a Liquid Dessicant De-humidifier?

Hello, everyone!! I am a Research scholar, working on the Liquid Desiccant Dehumidifier. For my personal interests, I wish to learn FLUENT based simulation in my current research. Any kind of help...

03 April 2017 3,283 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View