How can I measure MMP-1 protein activity or protein level from liver tissue?

Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?

03 March 2021 1,763 2 View

Binary Logistic Generalized Linear Mixed model in SPSS. Is it doable?

I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...

03 March 2021 2,297 3 View

Could you recommend any books about Number Theory?

Beginner level books. High level books. Analytical Number Theory. Algebraic Number Theory. Combinatorical Number Theory. Books about partitions. Books about primes.

03 March 2021 7,174 5 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Guidelines for survey (question type) analysis?

Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...

03 March 2021 2,037 3 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

No title

03 March 2021 5,360 2 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

How to model steel jackets using SeismoStruct?

Hi all, Does SeismoStruct support modeling rectangular RC columns retrofitted with steel jackets (e.g. rectangular, elliptical) ? Any suggestions for other software (apart from...

20 February 2021 4,521 1 View

Wave velocity and rock density paradox?

Practically it is known that seismic velocity increases as rock density increases, why then does the wave velocity equation involving elastic moduli and density indicate that velocity is inversely...

09 February 2021 1,843 3 View

How can the moment tensor inversion results can present good waveform fit (synthetic and observed waveform) from generalized Cut and Paste scheme?

Depending upon the distance of the seismic station from the epicentre, the quality of waveform data and the improvisation of the synthetic waveform on it is often a question. If the Pnl waveform...

31 December 2020 6,602 2 View

Petrel- well coordinates issue?

Hi, After loading 2D seismic lines in Petrel, I added three exploratory wells ( which supposed to be within the same 2D area) but these wells appears off the interesting area when I visualized...

25 October 2020 8,272 4 View

Is this possible ,to run model in seismostruct with out applied any load in load cases ?

Is this possible ,to run model in seismostruct with out applied any load in load cases ?

07 September 2020 3,499 2 View

How to identify the appropriate sites and design a passive seismic survey in order to support the site characterisation?

In the case of overpopulated cities, how I can select the appropriate sites to do some field measurements "Passive Seismic Surveys"? How about the design of the survey in order to study the soil...

04 August 2020 5,253 4 View

Could someone suggest good journal/article realted to energy dissipation through hysteretic behaviour?

Currently I am working on " Quantitative Assessment of dissipated energy from structural components correlation with deformation under seismic loads in low rise building using Perform 3D".

13 July 2020 3,330 2 View

What are the methods that can be used to predict the reasons behind bad seismic quality?

I will be highly appreciated if I get your answers in details.

15 June 2020 4,888 2 View

How to calculate the seismic force for a Pushover analysis and how to insert it in ETABS ?

One of the important ways in designing buildings with earthquake effects is through the American Seismic Code According to the attachment

20 April 2020 682 3 View

How should I calculate the seismic design loads for a short term service year i.e., 10 years ?

Based on ASCE7-10 provisions, seismic forces are calculated based on 2% probability of exceedance within a 50-year period (a mean recurrence interval of about 2475years). Due to the short...

13 April 2020 1,527 9 View