How can we accurately identify landslide seismic signals from low SNR raw data collected by seismic stations?

24 May 2024 0 3K Report

We know that only large-scale landslides can be detected by nearby seismic stations. In my research, I discovered that even landslides with volumes reaching millions or tens of millions of cubic meters are difficult to identify in raw seismic data. I am looking for an approach within the seismology field that can effectively identify target signals from low SNR raw data, which I can use to identify landslide seismic signals.

Badges
Science topic

More Feng Pu's questions See All

How does SEA software normally number subsystems?

Dear colleagues, What is the common subsystem numbering system in SEA modelling software (i.e. VA One, AutoSEA2)? Cheers, Feng

27 February 2021 7,073 3 View

Can a Golgi-stained dendritic spines picture processed by Image J be directly used for publication?

24 February 2021 3,348 2 View

How to extract dry soils such as rocks and Debris from Sentinel-2 images using Google Earth Engine?

17 December 2020 6,600 2 View

Why does the Abaqus simple tension simulation fail to converge for 2 elements perpendicular to load but not for 2 elements parallel to load?

I am simulating a simple uniaxial tension by pulling for a displacement of 0.4 in the Z-direction on a quarter symmetry cube with side lengths of 0.8. I am using an elastoplastic self-consistent...

08 September 2020 8,937 3 View

Can one find direct and elementary proofs for two integral formulas?

In the preprint W.-H. Li and F. Qi, A further generalization of the Catalan numbers and its explicit formula and integral representation, Authorea Preprints (2020), available online at...

24 August 2020 4,391 21 View

How to better control the sharp notch for an Abaqus Umat simulation?

I have a notched specimen as shown in attached NotchedSpecimen.png. It is basically a bar with 4 circular cuts on four sides. As a result, the specimen has 4 sharp notched edges. It is a quarter...

11 August 2020 7,018 4 View

With machine learning of images, how to make 'magnification' a factor in learning model?

Say we have microscope images obtained at various known magnifications. And I'd like the model to be able to tell that a big feature in a high magnification image is the same as a small feature in...

09 August 2020 4,289 5 View

How to Obtain the backscattering coefficient from the image using Google earth engine?

Dear All: I've only recently started studying the sentinel-1 image. I want to get the backscattering coefficient from the SAR image using the google earth engine. Please tell me...

04 July 2020 4,886 2 View

Weird bug with Abaqus boundary conditions?

I made a model and meshed it with quadratic tet and applied symmetry boundaries on the three flat surfaces. The model is pulled in tension by applying z-displacement on the back surface (not...

14 June 2020 6,819 3 View

Errors question about abaqus cohesive element ?

08 January 2020 2,353 1 View

I am looking for a microbend optical sensor design...can anyone please provide me some idea about it??

I am working on a landslide model...i need an optical sensor to determine the amount of pore pressure and other values..i am thinking of using a microbend sensor. Can anyone please provide me with...

11 February 2021 5,911 2 View

Wave velocity and rock density paradox?

Practically it is known that seismic velocity increases as rock density increases, why then does the wave velocity equation involving elastic moduli and density indicate that velocity is inversely...

09 February 2021 1,843 3 View

How can the moment tensor inversion results can present good waveform fit (synthetic and observed waveform) from generalized Cut and Paste scheme?

Depending upon the distance of the seismic station from the epicentre, the quality of waveform data and the improvisation of the synthetic waveform on it is often a question. If the Pnl waveform...

31 December 2020 6,602 2 View

How to download high quality DEM (resolution less than 5meter)?

I want high-quality DEM for our research purpose. High-quality DEM is used as a reference. I have generated the DEM through stereo images.

27 December 2020 8,614 15 View

What is New Next Generation Attenuation Relationships (NNGAR) and how are they different from other attenuation relationships?

Dear researchers The provisions of ASCE 7-10 states that New Next Generation Attenuation Relationships (NNGAR) has been used in the process of Probabilistic Seismic Hazard Analysis (PSHA) to...

15 November 2020 1,132 4 View

How to plot a Slope gardient Map of Bathymetry?

In order to find out the area/location prone to submarine landslide, plot of slope gradient map of Bathymetry is very helpful. Guide me, how to plot of slope gradient map (in detail/steps) of...

05 November 2020 8,144 4 View

Petrel- well coordinates issue?

Hi, After loading 2D seismic lines in Petrel, I added three exploratory wells ( which supposed to be within the same 2D area) but these wells appears off the interesting area when I visualized...

25 October 2020 8,272 4 View

Can we use distributed acoustic sensing in lab scale (~cm) applications?

I am looking for a way to increase the number of sensors in acoustic emission lab experiments. Fiber optics (DAS) is a natural candidate but the standard resolution is several meters. Is it...

20 September 2020 7,764 4 View

Is scaling period (T) recommended in seismic codes logical in order to scaling process of the earthquake records?

Dear researchers What is your opinion about the criterion recommended in seismic codes for determining scaling period, which are used to scale ground motion records? As you know, the mentioned...

27 August 2020 5,546 5 View

How to identify the appropriate sites and design a passive seismic survey in order to support the site characterisation?

In the case of overpopulated cities, how I can select the appropriate sites to do some field measurements "Passive Seismic Surveys"? How about the design of the survey in order to study the soil...

04 August 2020 5,253 4 View