05 October 2012 1 9K Report

Regarding atmospheric turbulence modelling

More Aman Raj Verma's questions See All
Make video by combining images

Can anyone help with software to combine images and make a video? I have continuous images of CFD simulation and I want to combine them as per order.

26 April 2012 3,394 10 View

decide volume fraction(vf) at air inlet in multiphase flow, Qa = air flow rate, Qw = water flow rate

I am injecting air over plate over which water is flowing(see domain attached), since vf = Qa/(Qa+Qw), Qw and vf are known through this Qa is calculated, and since air inlet dimension is known so...

04 April 2012 1,804 2 View

Volume fraction in FLUENT

how exactly is volume fraction defined in FLUENT, or if volume fraction of a =Qa/(Qa+Qb), then how can this be related to FLUENT

04 April 2012 1,834 1 View

Volume fraction in FLUENT

how exactly is volume fraction defined in FLUENT, or if volume fraction of a =Qa/(Qa+Qb), then how can this be related to FLUENT

03 April 2012 5,640 1 View

decide volume fraction(vf) at air inlet in multiphase flow, Qa = air flow rate, Qw = water flow rate

I am injecting air over plate over which water is flowing(see domain attached), since vf = Qa/(Qa+Qw), Qw and vf are known through this Qa is calculated, and since air inlet dimension is known so...

03 April 2012 9,544 2 View

Turbulent viscosity limited

What is the main reason for this prompt to came when a simulation is being done on FLUENT

03 April 2012 1,604 1 View

Multiphase flows

I am trying air injection to a normal flow of water over a flat plate to see the reduction in drag, what model must be suitable, VOF, Mixture, or Eulerian? Speed of water over plate is about...

29 March 2012 7,343 8 View

Enhanced Wall Treatment

I am working on a turbulent flow, I have read about enhanced wall treatment which is used to capture viscous sublayer. At very high Reynold's number (~10^7 or ~10^8) does this needed to be...

25 March 2012 8,645 8 View

Enhanced Wall Treatment

I am working on a turbulent flow, I have read about enhanced wall treatment which is used to capture viscous sublayer. At very high Reynold's number (~10^7 or ~10^8) does this needed to be...

02 March 2012 9,109 8 View

Can anyone recommend a software which can extract coordinates of image in pdf?

Can anyone recommend a software which can extract coordinates of image in pdf?

02 March 2012 4,894 13 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Which Scopus Journal provides the most affordable fees?

"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....

10 August 2024 8,621 1 View

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,992 0 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Who will be moral responsible for the death of thousands of people in the event of an earthquake?

Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...

08 August 2024 6,134 12 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Are there any instruments for studying time similar to the way it is in space?

There are a huge number of methods for studying objects in space, according to the senses (and not only). Mechanical, thermal, optical, acoustic, electrical, magnetic, based on particle beams,...

06 August 2024 7,102 0 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close