Volume fraction in FLUENT

04 April 2012 1 6K Report

how exactly is volume fraction defined in FLUENT,

if volume fraction of a =Qa/(Qa+Qb), then how can this be related to FLUENT

You can use constant volume fraction in the multiphase panel, so that you can the value appears in the bouandry layer conditions panel, but if it is a fonction , you can introduce it by creating an independent file as fluent define it in its help manual and when running the calculation you refer to the file by profile in define panel.

Badges
Science topic

More Aman Raj Verma's questions See All

decide volume fraction(vf) at air inlet in multiphase flow, Qa = air flow rate, Qw = water flow rate

I am injecting air over plate over which water is flowing(see domain attached), since vf = Qa/(Qa+Qw), Qw and vf are known through this Qa is calculated, and since air inlet dimension is known so...

04 April 2012 1,721 2 View

Volume fraction in FLUENT

how exactly is volume fraction defined in FLUENT, or if volume fraction of a =Qa/(Qa+Qb), then how can this be related to FLUENT

04 April 2012 1,715 1 View

Turbulent viscosity limited

What is the main reason for this prompt to came when a simulation is being done on FLUENT

03 April 2012 1,496 1 View

decide volume fraction(vf) at air inlet in multiphase flow, Qa = air flow rate, Qw = water flow rate

I am injecting air over plate over which water is flowing(see domain attached), since vf = Qa/(Qa+Qw), Qw and vf are known through this Qa is calculated, and since air inlet dimension is known so...

03 April 2012 9,448 2 View

Multiphase flows

I am trying air injection to a normal flow of water over a flat plate to see the reduction in drag, what model must be suitable, VOF, Mixture, or Eulerian? Speed of water over plate is about...

29 March 2012 7,252 8 View

Enhanced Wall Treatment

I am working on a turbulent flow, I have read about enhanced wall treatment which is used to capture viscous sublayer. At very high Reynold's number (~10^7 or ~10^8) does this needed to be...

25 March 2012 8,560 8 View

Can anyone recommend a software which can extract coordinates of image in pdf?

02 March 2012 4,808 13 View

Enhanced Wall Treatment

I am working on a turbulent flow, I have read about enhanced wall treatment which is used to capture viscous sublayer. At very high Reynold's number (~10^7 or ~10^8) does this needed to be...

02 March 2012 8,985 8 View

Multiphase flows

I am trying air injection to a normal flow of water over a flat plate to see the reduction in drag, what model must be suitable, VOF, Mixture, or Eulerian? Speed of water over plate is about...

02 March 2012 4,191 8 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View