Can someone explain the attached graphs?

I place different doping on X axis and get the following curves of efficiency parameters can someone body explain its behavior that why this increase and decrease come

04 May 2018 1,702 4 View

I am going to make the HIT CELL Bifacial so what changes i need to do so that it give me correct results?

I am going to make the HIT CELL Bi facial through AFORS HET Softwar so what changes i need to do so that it give me correct results

04 May 2018 7,872 0 View

With the addition of layer on solar panel why my short circuit current & Fill Factor get decrease?

i am adding ITO layer on crystalline silicon solar cell due to which my fill factor and short circuit current get decrease why this happen

01 February 2018 7,908 5 View

How to calculate the recombination and generation of HIT cell?

i am using AFORSHET software for simulation purpose now i need to improve my short circuit current for that i need to know about my generation and recombination so anybody tell me how i calculate it.

01 February 2018 1,557 3 View

In Suspended graphene SiO2 layer is removed by etching which eliminat charges in SiO2 and after annealing produce high quality graphene why?

plz answer instantly

03 April 2017 4,137 1 View

For which solar cell parameter is the upper limit set by the content of solar spectrum??

i think its short circuit current because short circuit current depend on the no of irradiation and their energy if higher energy and their content then higher will be the short circuit current...

11 December 2016 6,733 0 View

Do anyone here can help us in the field of molecular docking?

We have synthesized various metal complexes with different environment around the metals. Now to see the application of synthesized complexes we need this study also. we are also interested in...

01 March 2021 1,899 2 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

Distribution of particles in metal matrix?

How would define the "good" and "poor" distribution of particles within the matrix. Is there a quantitative solution to assess the distribution of the particles, which then having denotation of...

28 February 2021 7,397 8 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Which transition metal salt precursor is best for doping? Why?

I would like to synthesize a transition metal doped TiO2 via solgel method. Hence, I would like to know which metal salt precursor to choose among Chloride, Nitrate, and Sulphate. A clear...

27 February 2021 4,285 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

It is necessary to reflux the Schiff base and metal salts to obtain metal complex??

24 February 2021 9,166 3 View

Thermal reduction of graphene oxide.?

I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...

23 February 2021 4,155 4 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View